Reelcraft RT850-OLP Bruksanvisning
Reelcraft
trädgårds slang
RT850-OLP
Läs gratis den bruksanvisning för Reelcraft RT850-OLP (6 sidor) i kategorin trädgårds slang. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 1.5 recensioner. Har du en fråga om Reelcraft RT850-OLP eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/6
Operating Instructions
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com
Series RT Spring Driven Hose Reels
Low Pressure Model Numbers:
RT405-OLP RT605-OLP RT805-OLP
RT425-OLP RT625-OLP RT835-OLP
RT435-OLP RT635-OLP RT850-OLP
RT450-OLP RT650-OLP
Dimensions
• Ensure that reel is properly installed before connecting input and
output hoses.
• Bleed fluid/gas pressure from system before servicing reel.
• Before connecting reel to supply line, ensure that pressure does
not exceed maximum working pressure rating of reel.
• Remember, even low pressure is very dangerous and can cause
personal injury or death.
• Be aware of machinery and personnel in work area.
• If a leak occurs in the hose or reel, remove system pressure
immediately.
• A high tension spring assembly is contained within the reel.
Exercise extreme caution.
• Pull hose from reel by grasping the hose itself, not the control
valve.
• Ensure that reel, hose, and equipment being serviced are
properly grounded. Use an ohmmeter to check ground
continuity.
• If reel ceases to unwind or rewind, remove system pressure
immediately. Do not pull or jerk on hose!
• Treat and respect the hose reel as any other piece of machinery,
observing all common safety practices.
SAFETY
Personal injury and/or equipment damage may result if proper safety
precautions are not observed.
Form# 1121-802A Rev: 2/2023
A
17 7/8”
B
16 1/2”
C
6”
D
2 1/4”
E
See
page 6
.325
.325
.325
.325
.325
(4) PLACES
(4) PLACES
(4) PLACES
(4) PLACES
(4) PLACES
B
A
E
C
D
Series RT Spring Driven Hose Reels
Page 2
www.reelcraft.com
Installing the Input Hose
Mounting the Hose Reel
Prior to mounting the hose reel, ensure that the supply line pressure does
not exceed the maximum working pressure of the hose reel.
Do not exceed the maximum installation height of 16’ unless the reel was
specified differently when ordering. The maximum operating temperature
is 150 °F (66 °C).
Unpack and inspect the reel for damage. Turn the spool by hand to check
for a smooth operation.
Position the reel on the floor, wall or ceiling. Secure into place using four
mounting bolts (not included). See the included mounting template for
additional instructions for your specific mounting application. Depending
on where the reel is placed, it may be necessary to adjust the bumper stop
and guide arm to use the hose properly. See the instructions on the next
page to adjust the bumper stop and reposition the guide arm.
Use a flexible hose connection at input. Do not
use rigid plumbing. (input hose not included)
Apply pipe thread sealant to threads on stan-
dard reels.
Do not over tighten the connection.
Recommended torque should not exceed 70
ft./lb.
Mounting Applications
figure 1
figure 2
figure 3 figure 4
figure 5
Series RT Spring Driven Hose Reels
www.reelcraft.com
Page 3
Pull out the hose until the latch pawl is engaged.
The bumper stop may be adjusted by loosening the slotted
screws shown in figure 6.
Slide the bumper to the desired position and tighten the screws
BEFORE PULLING HOSE to disengage the latch pawl.
Adjusting the Bumper Stop
Removing the Guide Arm
Pull out hose until the latch pawl is engaged. Remove bumper
by removing the slotted screws (figure 6).
Disengage the latch pawl while maintaining a firm hold on
spool. Turn the spool hand over hand approximately two or
three revolutions in the direction of the drive spring until ten-
sion is removed.
Remove the 4 nuts holding the guide arm to base (figure 7).
figure 6
figure 7
Remove the guide arm and adjust to any of the seven
positions shown in figure 8.
See figures 2, 3, and 4, for recommended Guide Arm
positions for each mounting application.
Replace and tighten the 4 nuts.
Tighten the drive spring by turning the spool two or three
revolutions and engage the latch pawl.
Pull the hose through the roller opening in the guide arm
and replace the bumper stop (figure 6)
Positioning the Guide Arm
figure 8
Produktspecifikationer
| Varumärke: | Reelcraft |
| Kategori: | trädgårds slang |
| Modell: | RT850-OLP |
Behöver du hjälp?
Om du behöver hjälp med Reelcraft RT850-OLP ställ en fråga nedan och andra användare kommer att svara dig
trädgårds slang Reelcraft Manualer
21 Augusti 2025
21 Augusti 2025
trädgårds slang Manualer
Nyaste trädgårds slang Manualer
21 Augusti 2025
6 Augusti 2025
6 Augusti 2025
6 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
31 Juli 2025