Rolls Mic/Line Mixer RM82 Bruksanvisning
Rolls
Mixerkonsol
Mic/Line Mixer RM82
Läs gratis den bruksanvisning för Rolls Mic/Line Mixer RM82 (2 sidor) i kategorin Mixerkonsol. Guiden har ansetts hjälpsam av 11 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 6 recensioner. Har du en fråga om Rolls Mic/Line Mixer RM82 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
RM82
MIC LINE MIXER
Eight Channel Audio Mixer
Quick Start Guide
ROLLS CORPORATION
SALT LAKE CITY, UTAH
10/10
SPECIFICATIONS
Input Impedance: Mic: 10K XLR balancedΩ
1/4": 20K Ω unbalanced
Bus Input: 10K Ω unbalanced
Max Input Level: Mic: 0 dBV balanced
Line: +6 dBV
Input Connectors: 8: XLR, 8: 1/4" (Line), 1: RCA (Bus input)
Outputs: XLR bal., RCA unbalanced Prefade out
Max Gain: Mic: 55 dB
Line: 26 dB
Tone Control: 12 dB Treble/Bass cut
Phantom Power: +48 VDC
Output Level: +22 dBV max
Output Impedance: 51 Ω
Phase Shift: <10 degrees, 20Hz to 20 kHz
Max S/N ratio: 106 dB
THD: <.01%
CMRR: >52 dB (Mic)
Size: 19" x 1.75" x 6"
(48.3 x 4.5 x 15 cm)
Weight: 7 lbs. (3 kg)
DIP SWITCH DEFAULT SETTING: ALL OFF
JUMPER DEFAULT SETTING: 1/4” JACKS AS INPUT
MAIN OUTPUT AS LINE
OPERATION
CONFIGURING THE 1/4” INPUT JACKS AS DIRECT OUTPUTS
The eight 1/4” Input jacks come from the factory confi gured as line inputs and
are electrically mixed with the XLR jacks. They may be used together if desired.
To confi gure a channel’s 1/4” jack as a Direct Out, fi rst remove the RM82 lid.
For each channel there are dual three-pin headers with shorting jumper on two
pins. The setting from the factory is on “IN”. By moving the shorting jumpers to
the confi guration shown as “OUT” (one jumper up, the other down), the jack then
becomes a Direct Output.
CONFIGURING THE 1/4” INPUT JACKS AS INSERTS
To confi gure a channel’s 1/4” jack as an Insert, fi rst remove the RM82 lid and
locate the corresponding channel’s dual three-pin header. Move both shorting
jumpers down as shown below as “INSRT”, the jack then becomes an Insert.
Direct
Output
Insert Input
CONFIGURING THE OUTPUT FOR MIC OR LINE LEVEL
The RM82 ships from the factory with the XLR Main Output confi gured as Line
Level (+4 dB). To change this to Mic Level (-10 dB), carefully remove the lid,
locate the Mic/Line header which is near the Main Output jack. Move the two
jumpers from the Line Level position (shown below on the right), to the Mic Level
position (shown on the left).
Mic
Level
Line
Level
JUMPER DEFAULTS
The internal jumpers are confi gured from the factory as follows:
1/4” = INPUTS
MAIN OUT LEVEL = LINE LEVEL
Produktspecifikationer
| Varumärke: | Rolls |
| Kategori: | Mixerkonsol |
| Modell: | Mic/Line Mixer RM82 |
Behöver du hjälp?
Om du behöver hjälp med Rolls Mic/Line Mixer RM82 ställ en fråga nedan och andra användare kommer att svara dig
Mixerkonsol Rolls Manualer
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
Mixerkonsol Manualer
- Mackie
- Auna
- Apart
- Envivo
- Elysia
- TC Helicon
- RDL
- Redmond
- Aviom
- Peavey
- Zolid
- Golden Age Project
- Behringer
- Sunbeam
- Santos
Nyaste Mixerkonsol Manualer
2 April 2025
2 April 2025
31 Mars 2025
31 Mars 2025
31 Mars 2025
19 Mars 2025
16 Mars 2025
13 Mars 2025
13 Mars 2025