Sierra Designs Moken 6 Bruksanvisning


Läs gratis den bruksanvisning för Sierra Designs Moken 6 (2 sidor) i kategorin tält. Guiden har ansetts hjälpsam av 27 personer och har ett genomsnittsbetyg på 4.2 stjärnor baserat på 14 recensioner. Har du en fråga om Sierra Designs Moken 6 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/2
SIERRA DESIGNS 2011 Cherry Street, Unit 202 Louisville, CO 80027 Phone: 303-262-3050 Fax: 303-262-3051 Toll Free: 800-635-0461
insert
incorrect
correct
Figure 3: Hub Hook with Spider Hub
S I E R R A D E S I G N S
Figure 5: Clip Loc
MOKEN 6
Your Sierra Designs
MOKEN 6 tent is
very easy to pitch and
maintain. Follow these in-
structions to pitch your tent
quickly, safely and easily.
MOKEN 6 TENT CONTENTS
Tent Body & Rainfly: 1 Line Tighteners: 6
Sleeping Rooms: 2 Pitching Instructions: 1
Tent Poles: 4 Pole Sack: 1
Tent Stakes: 12 Stake Sack: 1
Guy Cords: 6
* Sierra Designs tents include stakes for pitching the body and
fly under normal conditions. Additional stakes may be required
in severe conditions.
Figure 2: Correct Pole Assembly
Figure 1: Main Pole with Spider Hub
Figure 4: Tent body (top view)
Figure 6: Toggle/Ring
First Pitch
In order to familiarize yourself with your new tent, we sug-
gest that you grab a friend or relative and do a “test pitch”
before you enjoy your outdoor adventure.
Select a Site
Pitch the tent on a level area that is protected from wind
and shaded from the sun, if possible. It also important that
the campsite drains well, in case of rain. Clear the area of
debris such as sharp stones and sticks that might abrade or
puncture the tent oor.
Assemble the Poles
The comes with 3 poles. The main pole is connect-Moken 6
ed via the Spider Hub(Figure 1) the remaining two poles
are of equal length with slight pre bends in them. Coming
from the center of the hub will be 4 longer poles and two
short poles. Assemble this pole first by carefully unfolding
the shock corded sections and allowing them to slide together.
Do not snap the pole sections together, as this could damage
the poles. Make certain that the insert for each pole section is
fully inserted into the next pole section, as well as, the “Spider
Hub (Figure 2). Failure to do so may cause the poles to break.
Once assembled place to the poles to the side.
Lay Out Tent Body
Unfold the tent body and lay flat on the ground so that the
blue and grey rainfly is facing up. You will notice that the in-
ner tents and common room footprint are already attached to
the rainfly. By having these parts pre assembled it will make
the initial set-up of your much easier. Spread the tent Moken 6
out so that you are able to nd the “Hub Hook(Figure 3).
This is located at the center of the tent (Figure 4, point M).
Once you have located the “Hub Hookyou will want to locate
the four navy blue stakeout loops (Figure 4, points A, B, G &
H). If you are pitching this tent by yourself we suggest that
you stake these four points down for an easier pitch.
Erect the Tent
Attach the “Hub Hookto the loop on the underside of the
“Spider Huband that the two short poles are facing the tent
doors. Now, start with the end of the longer pole that is fac-
ing point A (Figure 4) and insert the pole tip into one of the
grommets. Follow this step for point G and then move to the
other side of the tent and repeat with points B & H. Once the
main pole structure is up attach the Swift Clips and Clip Locs
(do not attach bungee yet) along the A-H and B-G axis. You
now have two main body poles left. Each one of these poles are


Produktspecifikationer

Varumärke: Sierra Designs
Kategori: tält
Modell: Moken 6

Behöver du hjälp?

Om du behöver hjälp med Sierra Designs Moken 6 ställ en fråga nedan och andra användare kommer att svara dig