StarTech.com IMC1GSFP Bruksanvisning

Läs gratis den bruksanvisning för StarTech.com IMC1GSFP (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 20 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 2 recensioner. Har du en fråga om StarTech.com IMC1GSFP eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: June 2, 2020 2:55 PM

Product Diagram (IMC1GSFP)

ComponentFunction

1PWR LED

• An external is Green:DC Power Source

detected.

• An external is not O:DC Power Source

detected.

2RJ45 Port

• Connect a to the Network DeviceMedia

Converter.

Green LED:

• A is detected.On:Network Device

• The is Flashing:Media Converter

transmitting/receiving data.

3DIP Switch

DIP 1:

• Enables Link Fault Pass Through (LFP) On:

function. LFP highlights link failures, by forcing

a link down between both connections during

a link failure.

• Disables LFP function (default).O:

DIP 2:

• Sets SFP speeds to 1000Mbps (default).On:

• Sets SFP speeds to 100Mbps.O:

4SFP LED

• Indicates that a link is detected on the Green:

SFP.

• Indicates that data is being Flashing:

transmitted or received.

5SFP Slot

• Connect an (100/1000BASE-X) to the SFP

Media Converter.

Industrial RJ45 to Open SFP Media Converter | 1000 Mbps (1G)

64-Pin Terminal Block

• Connect an external (12-56V DC Power Source

DC Input) to the .Media Converter

• Connect an alarm or warning circuit to the

relay (ALM) connection. The relay is triggered if

the loses power.Media Converter

7Ground Screw

• Connect a ground connection to the Ground

ScrewDC Power Source when connecting a to

the .Media Converter

Requirements

For the latest requirements, please visit www.startech.com/IMC1GSFP

• Network Equipment (ex. Router, Network Switch) x 1

• MSA-Compliant 100/1000BASE-X SFP Transceiver Module x 1

• RJ45 Terminated UTP/STP CAT5e (or better) Network Cable x 1

• Terminated Fiber Optic Cable (dependent on SFP Module) x 1

• DC Power Source x 1

• Phillips Head Screwdriver x 1

• Small Flat Head Screwdriver x 1

• Alarm or Warning Circuit x 1

Powering the Media Converter

Connecting and installing the must be completed by a 4-Wire Terminal Connector

licensed Electrician.

Notes: Make sure that you turn o the power source before connecting the power wire

to the .Media Converter

Do not exceed the recommend power source voltage as it may result in personal or

product damage.

1. Using a , loosen the two screws (+V-) on the Small Flat Head Screwdriver4-Wire

Terminal Connector (included).

2. Connect the from a (12 - 56V DC), or the provided Power WiresDC Power Source

Barrel Power Connector AdapterTerminal Block Connectors to the proper on

the . The terminals are marked on the Media ConverterMedia Converter’s Casing

(connect the positive wire to V+ and the negative wire to V-).

3. (Optional) Using a , loosen the two screws (ALM) on Small Flat Head Screwdriver

the .4-Wire Terminal Connector

12

356

7

4

Produktspecifikationer