Tado Wireless Temperature Sensor Bruksanvisning
Läs gratis den bruksanvisning för Tado Wireless Temperature Sensor (8 sidor) i kategorin Termostat. Guiden har ansetts hjälpsam av 19 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 10 recensioner. Har du en fråga om Tado Wireless Temperature Sensor eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/8
Manual for Professional
Installers
DIY Installation
If you are a professional installer, please not download the tado˚ app. There you will find specific installation instructions.
This manual is meant exclusively for professional installers. It includes generic instructions to install the Wireless
Receiver (Programmer) and the Wireless Temperature Sensor.
For the Starter Kit - Wireless Smart Thermostat V3+
(Incl. Programmer with Hot Water Control)
Manual version 3.2
A. Remove the battery
protection strip.
B. Press the button for
3 sec to start pairing.
C. Pairing may take up
to 2 min.
D. The static icon below
indicates successful pairing.
If pairing fails (E0), make sure the distance between the devices is approximately 3 meters. Pair again by pressing the
button for 3 sec.
2. Pair the Wireless Temp. Sensor
1. Install the Internet Bridge
A. Connect the Internet Bridge to the router.
If no free USB port is available on the router, use the
included 5V power adapter.
B. Press and hold the pairing button until the pairing LED
starts blinking.
2
min
3
sec
Solid on
Blinking
Unfold to check:
Step 4: Wire the Wireless Receiver
Step 5: Pair the Wireless Receiver
Step 6: Configuration
Extra information: Wireless Receiver Symbols
Power supply, testing
mode & configuration
Connection with
other tado˚ devices
Device errors Heat request Hot water request
If there is a wired room thermostat installed in the zone that is intended to be controlled by the Wireless Receiver,
please by bridging the control wires and insulating the other wires with the included 2-terminal decommission it
connector blocks as shown in the images.
Once tado° is installed, the Wireless Receiver will be the only device that controls the heating system.
For Neutral and Earth, Insert only one wire per block, even though the block has more than one opening.
3. Replace the room thermostat
LIVE
(COM) NEUTRAL EARTH
SWITCHED
LIVE (NO)
Caution! Turn OFF the
power before wiring!
Produktspecifikationer
| Varumärke: | Tado |
| Kategori: | Termostat |
| Modell: | Wireless Temperature Sensor |
Behöver du hjälp?
Om du behöver hjälp med Tado Wireless Temperature Sensor ställ en fråga nedan och andra användare kommer att svara dig
Termostat Tado Manualer
23 September 2024
23 Augusti 2024
Tado Smartes Heizkorper Thermostat Thermostaat Bruksanvisning
10 Augusti 2024
7 Augusti 2024
6 Augusti 2024
6 Augusti 2024
4 Augusti 2024
Termostat Manualer
- Junkers
- EQ-3
- Cepra
- Daikin
- Amfra
- Honeywell
- Finder
- Weishaupt
- Hunter
- Brennenstuhl
- MundoControl
- HomeMatic
- Wodtke
- THERMAFLEX
- Qubino
Nyaste Termostat Manualer
14 Juni 2025
9 April 2025
7 April 2025
7 April 2025
6 April 2025
6 April 2025
6 April 2025
5 April 2025
4 April 2025