Taramp’s HD 10000 Bruksanvisning
Läs gratis den bruksanvisning för Taramp’s HD 10000 (8 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 2 recensioner. Har du en fråga om Taramp’s HD 10000 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/8
The installation of this product must be made by a qualified professional.
Instruction manual
AMPLIFIER - 10.000W RMS - 1 OHM
Index
TARAMPS, located – Alfredo Marcondes, SP - Brazil, ZIP at Julio Budisk highway, SN, KM 30
CODE 19180-000, warrants this product against any defects on terms of project, making,
assembling, and/or with solidarity, due to project vices which cause it improper or
inadequate to its original use within 12 months from the date of purchase. In case of defect
during the warranty period, TARAMPS responsibility is limited to the repairing or
replacement of the device of its own making.
This warranty excludes:
•Damaged products by improper installation, water infiltration, violation by unauthorized
individuals;
•Cases in which the product is not used in adequate conditions;
•Damage of any kind, due to problems in the product, as well as losses caused by discontinued
use of the product.
•Tamper or torn warranty seal;
•The product with damage from falling, bumps or nature related problems (flooding,
lightning, etc);
•Costs involving uninstallation, reinstallation of equipment as well the shipment to the
factory;
•Warranty card is not properly filled or torn;
•Defects caused by accessories, modifications or features attached to the product;
Term of warranty
Technical assistance
For international support, check on our website:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: service@taramps.com.br
www.taramps.com.br/en/rede-de-assistencias-tecnicas or contact direct the factory support:
01
04 • Output & power supply connector
03 • Functions & inputs
•Protection system
01 • Term of warranty
• Safety
05 • Installation
• Recommended wire gauge & fuse
• LEDS indicator
• Technical assistance
06 • Technical features
• Safety requirements
02 • Introduction
02
Safety requirements
Introduction
Taramps reserves the right to modify the contents of this document at any time without prior notice and does
not have the obligation to apply the changes in units which were previously produced.
Pay attention to the safety symbols.
Safety
This symbol with “CAUTION” is intended to alert the user to the presence of
important instructions. Failure to heed the instructions will result in risk of
injury to user or product damage.
CAUTION
Read this manual before preparing the product. In case of
doubt, contact our technical support: ( or18) 3266-4050
www.taramps.com.br.
At the end of its useful life, this product must not be
disposed of in household waste. Look for an
electronic equipment collection or recycling center
for proper disposal.
Declaration of Conformity
TARAMPS ELECTRONICS LTDA
Alfredo Marcondes - SP
Brazil
Hereby, Taramps Electronics Ltda declares that the
product HD 10,000 complies with the Directive
2014/30/EU, according with the following harmonized
standard:
-EN 50498:2010
Electromagnetic compatibility (EMC) -
Product family standard for aftermarket
electronic equipment in vehicles
The full text of the EU Declaration of Conformity is available at
the following Product Page on Internet.
- This amplifier is for use with 12V batteries. Always check the voltage before installing.
- This amplifier may produce high sound pressure levels. Avoid continuous exposure to levels
over 85dB to prevent permanent hearing loss.
- Wear safety glasses, insulated gloves and correct tools for installing this product.
- This amplifier must be installed in a firm place with at least 1” space around the heatsink for
proper heat spreading.
- The installation of this amplifier must be done by a qualified professional.
- Never install the amplifier in places exposed to dust, humidity and water. Pay attention to
install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.
To ensure proper use, please read through this manual before using the amplifier. It is
specially important that you know the CAUTIONS contained here.
- Before make any connection to amplifier, disconnect the battery negative terminal.
- When in use, the external surface of may amplifier becomes hot. Avoid touching the heatsink
area and keep childrens far from the amplifier.
- If you want to dispose this amplifier, don't throw it on domestic waste. It must be collected by
an used electronic product disposal service for proper recycling.
- Output connections for speakers may have voltage levels when the amplifier is operating.
Make sure that the amplifier is turned OFF before proceed any connection or disconnection in
this terminals.
- Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating
as indicated here in this manual. Use of improper fuse or circuit breaker could result in
overheat, smoke, damage to product, injury or burns.
- Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect
any wires routed through car's body.
Produktspecifikationer
| Varumärke: | Taramp’s |
| Kategori: | mottagare |
| Modell: | HD 10000 |
Behöver du hjälp?
Om du behöver hjälp med Taramp’s HD 10000 ställ en fråga nedan och andra användare kommer att svara dig
mottagare Taramp’s Manualer
4 Juli 2025
4 Juli 2025
2 Juli 2025
2 Juli 2025
9 Juni 2025
mottagare Manualer
- Polk
- Gefen
- Galaxy Audio
- Plantronics
- Engel Axil
- Monacor
- Selfsat
- JETI
- Chandler
- GoGEN
- Sonance
- Salora
- Sunstech
- Key Digital
- Fosi Audio
Nyaste mottagare Manualer
4 Juli 2025
2 Juli 2025
1 Juli 2025
30 Juni 2025
29 Juni 2025
29 Juni 2025
26 Juni 2025
26 Juni 2025
26 Juni 2025
24 Juni 2025