Velleman BATTEST 2 Bruksanvisning
Velleman
Inte kategoriserad
BATTEST 2
Läs gratis den bruksanvisning för Velleman BATTEST 2 (5 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 9 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 5 recensioner. Har du en fråga om Velleman BATTEST 2 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/5
BATTEST2 - 1 - VELLEMAN
BATTEST2 – MULTI-PURPOSE BATTERY TESTER WITH LCD DISPLAY
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm
the environment.
Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialised
company for recycling.
This device should be returned to your distributor or to a local recycling service.
Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for buying the BATTEST2! Please read the manual thoroughly before bringing this device into service. If the
device was damaged in transit, don't install or use it and contact your dealer.
2. General Guidelines
• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer
will not accept responsibility for any ensuing defects or problems.
• Do not use rechargeable batteries to power your . BATTEST2
• Only test one battery at the time.
• Do not modify or disassemble the device.
3. Use
1. To power the battery tester, remove the battery cap at the back of the device. Insert 1 x 1.5V AAA alkaline battery
respecting the polarity. Replace the battery cap.
2. Insert the battery you would like to test into the corresponding test channel (for CRV3, CR5 and CRP2 batteries,
9V, 3V and 1.5V button cells) or slot (CR2, CR123A, N, AA, AAA, C and D type batteries). Make sure the battery
is firmly placed respecting the polarity. The battery condition will be shown on the LCD display (see fig. below).
3. Remove the battery after checking.
REMARKS: Make sure the battery is correctly placed into the slot or the test channel. Remove the battery powering
the when not in use to avoid battery leakage. Use a fresh alkaline battery to run the tester to BATTEST2
ensure accurate testing results.
4. The LCD Display
LCD Display Battery Condition
1 – 5 marks (POOR) The battery is empty. Recharge a rechargeable battery or dispose of the battery
respecting the local rules.
6 – 10 marks (FAIR) Battery with limited power but can still be used for a limited time.
11 – 18 marks (GOOD) Battery has adequate power.
5. Technical Specifications
Power Supply 1 x 1.5V AAA battery
Dimensions 118 x 88 x 23mm
The information in this manual is subject to change without prior notice.
Produktspecifikationer
| Varumärke: | Velleman |
| Kategori: | Inte kategoriserad |
| Modell: | BATTEST 2 |
Behöver du hjälp?
Om du behöver hjälp med Velleman BATTEST 2 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Velleman Manualer
26 Mars 2025
3 Mars 2025
2 Januari 2025
31 December 2025
31 December 2025
9 December 2024
9 December 2024
9 December 2024
9 December 2024
9 December 2024
Inte kategoriserad Manualer
- Singularity Computers
- MB Quart
- Gefen
- Tovsto
- Fujifilm
- Rollei
- X Rocker
- Audiovox
- Carrier
- Lifespan
- Procare
- Grothe
- Yato
- Ravanson
- Blebox
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025