Velleman VTTEST 7 Bruksanvisning


Läs gratis den bruksanvisning för Velleman VTTEST 7 (16 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 11 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 6 recensioner. Har du en fråga om Velleman VTTEST 7 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/16
VTTEST7 VELLEMAN
1
VTTEST7 - BATTERY TESTER
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm
the environment.
Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialised
company for recycling.
This device should be returned to your distributor or to a local recycling service.
Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Your new is a sensitive and accurate device for testing batteries under charge. You can test standard zinc VTTEST7
carbon, alkaline, mercury, silver oxide, lithium and nickel cadmium batteries.
2. Operation
a) Select the correct battery type and voltage with the recessed range switch. Examples:
- move the range selector to the position labelled "1.5V AA D" if you wish to test AA-C- - - -, C or D batteries of 1.5V.
- select the "9V" tion to test rectangular 9V-posi -batteries.
- select the "BUTTON CELL 1.5V" position to test mercury, silver or alkaline button cells.-
- select the "LITHIUM 3V" position for lithium button cells.-
- -C-select the "1.5V AA D"-position to test nickel cadmium batteries of 1.25V and read the value on the lowest of
the three scales on the analogue display.
The value indicated on the meter is the load current drain placed on the battery during the check.
CAUTION: Selecting the wrong range will yield inaccurate results. You may also damage the device in the process.
b) Place the red probe tip (+) against the positive (+) battery terminal and the black probe tip ( ) against the negative (- -)
battery terminal.
CAUTION : Mind the polarity indications when testing your batteries!
Select the correct range (see above). Use the following procedure to test your batteries:
- Place the battery's negative ( ) terminal against the 's negative ( ) contact and touch the battery's - VTTEST7 -
positive (+) terminal with the red probe tip (+).
- In order to test rectangular 9V-batteries : place the battery's negative ( ) terminal against the 's negative - VTTEST7
(-) contact and place the battery's positive (+) terminal against the 's positive (+) contact.VTTEST7
- In order to test button cell batteries: insert the battery in the slot on the side of the device. Make sure the negative
(-) pole is facing up and press the brown switch on the front panel.
CAUTION : Observe the following safety prescriptions in order to avoid all damage to the button cell being tested:
- Do not push the brown switch when using the probe tips to test a button cell.
- Do not allow the red probe tip (+) to contact the black probe tip ( ) when using the 9V- -contacts to test button cells.
c) Read the analogue display to determine the condition of the battery.
- Use the upper scale ("REGULAR") for measuring regular zinc carbon and alkaline batteries.
- Use the centre scale ("BUTTON CELL LITHIUM") for measuring mercury, silver oxide, alkaline and lithium -
button cells.
- Use the lower scale ("NICKEL CADMIUM") for measuring rechargeable nickel cadmium batteries.


Produktspecifikationer

Varumärke: Velleman
Kategori: Inte kategoriserad
Modell: VTTEST 7

Behöver du hjälp?

Om du behöver hjälp med Velleman VTTEST 7 ställ en fråga nedan och andra användare kommer att svara dig