ABB DY365 4CE Bruksanvisning

ABB Inte kategoriserad DY365 4CE

Läs gratis den bruksanvisning för ABB DY365 4CE (1 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 5 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 3 recensioner. Har du en fråga om ABB DY365 4CE eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/1

User manual

DY365 4CE REMOTE ACTUATOR

Read all instructions carefully

• The DY365 4CE remote actuator is a four-relay electronic device that receives the command signals

from the switch via DY365 I/O extension ports.

It performs actions of 1B type and is intended to operate in a domestic and similar environment

with overvoltage category III and normal pollution degree (EN 60730-1).

SAFETY WARNINGS

During product installation and operation it is necessary to observe the following

instructions:

1) The device must be installed by a qualiﬁed person

2) Before accessing the terminals, make sure that the leads are not live

3) Do not power the device if any part of it is damaged

4) Connect the product following the diagrams described in this manual

5) In the electrical system upstream of the device must be installed a switch and a

protection device against the overcurrents.

6) The product must be installed and activated in compliance with current electric

systems standards.

7) After installation inaccessibility to the terminals without using dedicated tools

must be guaranteed.

Code Model Description

2CSM221181R1000 DY365 4CE 4-channel remote actuator

TECHNICAL FEATURES

• Power supply: 12/24 V AC/DC (-15%/+10%) 50/60 Hz

• 4 relays normally open 8A / 250 V AC

• I/O extension port for connection to the switchDY365

• Operating temperature: 0 ÷ +50 °C

• Storage temperature: -25 ÷ +70 °C

• Container: 4 DIN modules

• Protection degree: IP20 (IP40 when correctly installed in the electrical panel)

OPERATION

• When switched on, the red LEDs emit 2 ﬂashes lasting half a second (switch-on sequence).

• Once the switch-on sequence is completed, the green LED is lit to indicate normal device

operation and the red LEDs are turned on/off to indicate the corresponding status of the

4 channels (on = ON).

Channels conﬁguration

• During normal operation, press and hold the SET button for at least 3 seconds to enter

in conﬁguration mode. In this mode the green LED is off while the red LED

corresponding to the relay to be conﬁgured ﬂashes.

• To select the relay to be associated with the channel of DY365 switch , press the SET

button until the red LED for the relay to be conﬁgured ﬂashes.

• Once the channel is selected, the actuator remains in conﬁguration mode for 60 seconds:

activate the channel conﬁguration on the DY365 switch.

To activate the channel conﬁguration, see the DY365 switch user manual.

• Once the relay conﬁguration is complete, the actuator resumes normal operation

• To cancel the conﬁguration of a channel, enter the conﬁguration mode, select the channel

with the SET button (relative red LED ﬂashing), then press the SET button for at least three

seconds until the green LED lights up again.

Each new conﬁguration cancels the previous conﬁguration

REFERENCE STANDARDS

Compliance with Community Directives:

2014/35/EU (LVD)

2014/30/EU (EMCD)

is declared in reference to the harmonized Standards:

EN 60730-1

EN 301 489-1/3 and EN 300 220-3

Description

Connection diagram

8 A / 250 V ~

8 A / 250 V ~ 8 A / 250 V ~ 8 A / 250 V ~

Out 1

Out 2 Out 3 Out 4

I/O extension port

(B) (A)

 Green LED for operating status signaling

 Red LEDS for relay status signaling

 SET BUTTON for channels programming and resetting

Dimensions (mm)

87 mm

72 mm

45 mm

60 mm

65 mm

DY365 4CE

2CSM441048D0201

ABB S.p.A

V.le dell’Industria 18

20010 Vittuone (MI) - Italy

Tel. +39 02 2415 0000

https://new.abb.com/low-voltage

We reserve the right to make technical changes or modify

the contents of this document without prior notice.

Installation Manual







Produktspecifikationer

Varumärke:	ABB
Kategori:	Inte kategoriserad
Modell:	DY365 4CE
Färg på produkten:	Black, White
Vikt:	23000 g
Bredd:	550 mm
Djup:	920 mm
Höjd:	1160 mm
Antal program:	17
Transport wielen:	Ja
Träningsparametrar visas:	Calories, Distance, Evolutions per minute (RPM), Heart rate, Speed, Time
Max användarvikt:	100 kg
Flaskhållare:	Nee
Svänghjulets vikt:	6000 g
Pulsmätare som tillval:	Nee
Kör system:	V-riem
Standard pulsmätare:	Handgreepsensoren
Sadeljustering:	Verticaal/Horizontaal