Allen-Heath SQ Dante Bruksanvisning
Allen-Heath
Processor
SQ Dante
Läs gratis den bruksanvisning för Allen-Heath SQ Dante (2 sidor) i kategorin Processor. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.2 stjärnor baserat på 1.5 recensioner. Har du en fråga om Allen-Heath SQ Dante eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
M- -SDANTE Fitting Note SQ
AP11431 Issue 2
SQ Dante Option Card
M- -SDANTE is one of several audio networking options that can be fitted to SQ
an Allen & Heath mixer. It provides a 64x64ch 48/96kHz interface to a Dante SQ
network.
Fitting the card
1. Switch the system off.
2. Use a Torx T8 driver to remove the 2 screws securing the I/O Port
blank panel the SQ mixer. to
3. Slide the card into the slot and press it firmly into the mating
connector.
4. Refit the 2 screws to secure the card.
Control Network Bridge
Go to the screen to switch on Control Setup / Audio I/O Port/
Network Bridge. This connects the SQ Network Port and I/O Port
control networks.
The Control Network Bridge does not pass audio.
Connecting to a network that includes a DHCP server
(such as a router) can change the IP address of the Dante
card. Therefore it is recommended that the network is
only bridged when necessary.
Software and firmware
Download and install the latest version of firmware: SQ
http://www.allen-heath.com/sq-software
M- -SDANTE requires firmware V1.2.2 or above. SQ SQ
Go to the Audinate website to learn more about Dante, and to download software
including Dante Controller and Dante Virtual Soundcard (DVS):
http://www.audinate.com/
Front panel
Setting clock and patching signals
Use the screen to patch signals from or to the I/O Port. SQ I/O
Use the screen to select the clock source for the Setup / Audio Audio Sync/
mixer. Typically, this is set to Internal, unless the mixer is syncing from the Dante
card (clock slave), for example in a digital split setup.
For more information on setup and functions please SQ
refer to the Firmware Reference Guide available for SQ
download from www.allen-heath.com.
Use to patch signals to/from other devices, and configure the Dante Controller
sample rate and clock settings for the card.
If you set the mixer clock to Internal, select Enable Sync
To External. To clock other Dante devices to this option
card, select . Preferred Master
A limited one year manufacturer’s warranty applies to this product, the conditions
of which can be found at: www.allen-heath.com/legal.
This product complies with the European Electromagnetic
Compatibility directive 1 U and the European Low Voltage 20 4/30/E
directive / U. 2014 35/E
Copyright © 2018 Allen & Heath. All rights reserved.
ALLEN HEATH &
Allen & Heath Limited, Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK
http://www.allen-heath.com
Link Status
Flashes to indicate
network activity
Dante ports
A built-in Gigabit
switch with 2 locking
EtherCon ports for
redundant or switch
mode operation
Produktspecifikationer
| Varumärke: | Allen-Heath |
| Kategori: | Processor |
| Modell: | SQ Dante |
Behöver du hjälp?
Om du behöver hjälp med Allen-Heath SQ Dante ställ en fråga nedan och andra användare kommer att svara dig
Processor Allen-Heath Manualer
3 Augusti 2025
3 Augusti 2025
3 Augusti 2025
3 Augusti 2025
3 Augusti 2025
3 Augusti 2025
3 Augusti 2025
Processor Manualer
- Tempo
- Matrox
- Toa
- Henry Engineering
- HP
- Arturia
- Warm Audio
- Yamaha
- AuviTran
- Black Lion Audio
- Fredenstein
- Intel
- Mathew Lane
- Bose
- Chandler
Nyaste Processor Manualer
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
1 Augusti 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025