Ctek D250SA Bruksanvisning
Sidor 12 Engels Batteriladdare
Läs bruksanvisningen för Ctek D250SA gratis online eller ladda ner PDF:en. 37 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
EN•3
EN
MANUAL
CONGRATULATIONS
on the purchase of your new CTEK charger providing professional battery care. This charger is
included in a series of professional chargers from CTEK SWEDEN AB and represents the latest
technology in battery charging. With the CTEK D250SA and SMARTPASS 120 you can be sure of
getting maximum performance from your dual battery system.
SAFETY
CALIFORNIA PROPOSITION 65
WARNING: This product contains chemical known to the state
of California to cause cancer or reproductive toxicity.
• The D250SA and SMARTPASS 120 have been developed for 12V lead-acid batteries. Do not use
the unit for any other type of battery.
• Wear protective goggles when connecting and disconnecting batteries.
• Battery acid is corrosive. Rinse with plenty of water immediately if you get acid on your skin or in
your eyes. Get medical assistance.
• Never use a charger with damaged electric cables. Check that the cables have not been dama-
ged by hot surfaces, sharp edges or in any other way.
• Explosive gases are generated while lead-acid batteries are being charged. Avoid any sparking
near the battery. Use in a well-ventilated location.
• Never place the charger above the battery, and avoid covering the charger during charging.
• Disconnect the battery terminal posts before installing.
• The D250SA and SMARTPASS 120 are not spark-free.
• The installation must include a fuse in accordance with the recommendations in the table
”CABLE AND FUSE RECOMMENDATIONS”.
WARNING!
The D250SA and
SMARTPASS 120 are not
protected against reversed
polarity.
Remember that all installations in boats must comply with ISO 10133!
1. The cabling from the batteries must have fuses near the batteries.
2. The batteries must be securely fastened in a ventilated space.
3. The cabling must be run through pipe ducting, separately from 230V/110V wiring (mains power),
or secured by clips at every 30 cm/1 ft.
4. Cabling in the engine compartment must be temperature rated at 70C/ 158F.
Temperature sensor 2 m/6 ft.
Smart alternator cable (red) 0.2 m/0.6 ft.
AGM Cable (black)
0.2 m/0.6 ft.
SMARTPASS 120
+OUT
+OUT
+IN
Negative cable connection (M8) 0.3 m/1 ft.
Connector plate
D250SA
SMARTPASS 120
Temperature sensor 2 m/6 ft.
+IN Input Alternator+OUT Output Service battery
+IN Input Alternator+OUT Output Service battery
+IN Input Solar panelEarth Connection
+OUT Output Consumers
Produktspecifikationer
| Varumärke: | Ctek |
| Kategori: | Batteriladdare |
| Modell: | D250SA |
Behöver du hjälp?
Om du behöver hjälp med Ctek D250SA ställ en fråga nedan och andra användare kommer att svara dig
Batteriladdare Ctek Manualer
Ctek MXS 7.0 Bruksanvisning Ctek I1225 Bruksanvisning Ctek M25 Bruksanvisning Ctek MXS 10.0 Bruksanvisning Ctek Onyx Bruksanvisning Ctek XS 7000 Bruksanvisning Ctek Bumper 120 Bruksanvisning Ctek Pro Battery Tester Bruksanvisning
Alla Ctek Batteriladdare manualer
Populära i Batteriladdare
Ctek READY AUTOMOTIVE Bruksanvisning Ctek MXS 5.0 POLAR Acculader Bruksanvisning Ctek MXS 5.0 CHECK Acculader Bruksanvisning
Batteriladdare Manualer
Nyaste Batteriladdare Manualer
V7 CHGCT36USBCPD-2N Bruksanvisning Scanstrut SC-USB-01 Bruksanvisning Scanstrut SC-CW-04E Bruksanvisning Scanstrut SC-CW-06E Bruksanvisning Scanstrut SC-CW-01E Bruksanvisning Fuxtec FX-E1LG1A Bruksanvisning Voltcraft Charge Manager 410 Bruksanvisning Envivo ENV-1597 Bruksanvisning Jackery Explorer 240 v2 Bruksanvisning Jackery Explorer 1000 v2 Bruksanvisning