EXSYS EX-48200I Bruksanvisning


Läs gratis den bruksanvisning för EXSYS EX-48200I (2 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 15 personer och har ett genomsnittsbetyg på 4.2 stjärnor baserat på 8 recensioner. Har du en fråga om EXSYS EX-48200I eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/2
6 5
Die EX 48200I ist eine M.2 Karte zur Umsetzung auf zwei RS 232 Schnittstellen mit FIFO - -
16C550 Port für den Anschluss von High Speed Seriellen RS 232 Peripherie Geräten (z.B. -
Modem, Plotter usw.). Die EX 48200I nutzt den Exar Chipsatz, der die neueste High Speed- - -
Interface Technologie beinhaltet. Die Karte gewährleistet so eine sichere Datenübertragung und -
exzellente Performance von bis zu 921.6 KBaud/s für jedes angeschlossene serielle Gerät! Sie
unterstützt den M.2 NGFF Bus mit A Key. Es ist nicht möglich die I/O Adressen und Interrupts -
manuell einzustellen, da die Einstellungen der Karte vom System (BIOS) und beim installieren
des Betriebssystems automatisch vorgenommen werden. Zusätzlich ist die EX 48200I mit einer -
2.5KV optischen Isolation ausgestattet.
Kompatibilität: M.2 NGFF mit A Key -
Betriebssysteme: Windows 200x/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx/ Linux/ QNX 6.0
Lieferumfang: EX 48200I, 2x Flachbandkabel, Treiber CD, Anleitung -
Zertifikate:
1
BESCHREIBUNG & TECHNISCHE DATEN
AUFBAU
Anleitun
Vers. 1.0 / 20.02.19
E 48200
ANSCHLÜSSE
COM1&COM2: 2x 10 Pin Floppy Anschluss für
- RS 422/485 9 Pin Flachbandkabel
9 Pin Stecker Seriell RS 232-
Pin Signal Pin Signal
1 DCD 6 DSR
2 RXD 7 RTS
3 TXD 8 CTS
4 DTR 9 RI
5 GND
DB 9M
HARDWARE INSTALLATION
DRIVER INSTALLATION
Please note the following installation instructions. Because there are large differences between the
PC’s, we can give you only a general installation instructions for the EX-48200I. Please refer your
computer’s reference manual whenever in doubt.
1. Turn off the power to your computer and any other connected peripherals.
2. Remove the mounting screws located at the rear and/or sides panels of your Computer and
gently slide the cover off.
3. Now connect the two Ribbon Cable with the 10 Pin Floppy Connectors at the EX 48200I. -
4. Locate an available M.2 NGFF expansion slot and insert the card. Make sure that the card is
plugged in correctly.
5. Gently replace your computer’s cover and the mounting screws.
Windows 200x/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx
After starting Windows is recognizes a new . Insert the driver CD into „Serial PCI Connector“-
you CD ROM drive (eg drive D:) and then start the installer -„xr17v35x_win_single_installer“
which located in folder „Ver_5100_installer_uninstaller“ (see picture). Follow the installation
instructions and finish the installation:
CHECK INSTALLED DRIVER
Open the > <. Now you should see at Device Manager-Ports (COM & LPT) Multiple and at
Connection Adapter (serial) the following new entry‘s:
If you see this or a similar information the device is installed correctly.
DRIVER INSTALLATION
Windows CE
After starting Windows is recognizes a new . Insert the driver CD into „Serial PCI Connector“-
you CD ROM drive (eg drive D:) and then use the driver which located in the folder „windows -
CE 6 7“ (see picture):
Linux
After starting Linux is recognizes a new . Insert the driver CD into you „Serial PCI Connector“-
CD ROM drive (eg drive D:) and then use the driver which located in the folder „Linux“ (see -
picture):
QNX
After starting the system is recognizes a new . Insert the driver CD into „Serial PCI Connector“-
you CD ROM drive (eg drive D:) and then use the driver which located in the folder „QNX“ (see -
picture):


Produktspecifikationer

Varumärke: EXSYS
Kategori: ej kategoriserat
Modell: EX-48200I

Behöver du hjälp?

Om du behöver hjälp med EXSYS EX-48200I ställ en fråga nedan och andra användare kommer att svara dig