Heatit Z-Wave Plus Bruksanvisning
Läs gratis den bruksanvisning för Heatit Z-Wave Plus (4 sidor) i kategorin Termostat. Guiden har ansetts hjälpsam av 24 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 12.5 recensioner. Har du en fråga om Heatit Z-Wave Plus eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
Ver 2016-B
IMPORTANT!
PLEASE READ THIS BEFORE INSTALLATION.
This thermostat is tested and certified by Pepper One Gmbh
according to the requirements put forward by the Z-Wave
Alliance. This is a Z-wave Plus product with the 500 series chip.
If the product does not work with your gateway, then the
gateway manufacturer has not made an integration or
implemented such a thermostat with their gateway.
We do not give any guarantee towards integration.
PRINCIPLES FOR REGULATION
The Heatit Z-Wave thermostat is designed for controlling
electrical heating cables and electrical radiators/convectors.
The thermostat has 2 internal temperature sensors and has
3 algorithms for temperature compensation. After you have
set the temperature, the thermostat will use a hysteresis to
regulate the temperature. The hysteresis is adjustable.
TEMPERATURE SHOWN IN DISPLAY
The temperature shown in the display is the actual temperature
for floor sensor and the external room sensor. You are able to
calibrate the sensor values.
When using the internal room sensor, the temperature shown
is the set point. When using the internal sensor, the thermostat
can seem somewhat inaccurate. This is due to heat generation
inside the thermostat, draft and other external influences.
If the thermostat is to be used with waterbased heating systems,
you have to use an external sensor.
SETUP
This manual describes the most essential functions and
technical specifications of the thermostat. These instructions
help the user to control the thermostat, and the electrician
to install and setup the thermostat.
INSTALLATION
Installation must be done by a qualified electrical installer in
accordance with the National Building codes. Before installation,
disconnect any power to the thermostat’s mains. During
installation of the thermostat, power to the thermostat must
be disconnected AT ALL TIMES!
Use e.g. a small slotted screwdriver. Start by carefully removing
the front cover by pushing the release springs. The front cover
and the frame can now be removed.
Now connect the wires to the thermostat’s terminals:
HEATING (N) Heating cable connection (Neutral)
N Power connection (Neutral) 230V
L Power connection (Live) 230V
HEATING (L) Heating cable connection (Live)
PILOT Pilot signal (ECO temp) 230V
FLOOR SENSOR NTC type (10, 12, 15, 22, 33 or 47kΩ).
Default 10kΩ.
EXTERNAL SENSOR NTC type (10, 12, 15, 22, 33 or 47kΩ).
Default 10kΩ.
Next, position the thermostat and fasten it onto the wall’s
mounting box using 2-4 screws. Position the frame, then
position and carefully press the front cover until it snaps in
place. Check that the front cover has snapped in place properly
on both left and right side. The front cover should now be firmly
fixed on all sides.
STARTUP
AFTER CONNECTING THE POWER TO THE THERMOSTAT FOR THE
FIRST TIME, ALL PARAMETERS WILL HAVE DEFAULT SETTINGS.
2 yr
HEATIT
Z-WAVE
Installers manual
Firmware 1.8
01.06.2016
Release spring
1: Left 3: Right2: Center
87 mm
58,8 mm
HEATING L
L
N
HEA
TING N
PILOT WIRE
FL OOR
SENSOR
EXTERNAL
SENSOR
Made in EU
TF 021
21,3 mm
51,1 mm
87 mm
58,8 mm
29,9 mm
Produktspecifikationer
| Varumärke: | Heatit |
| Kategori: | Termostat |
| Modell: | Z-Wave Plus |
Behöver du hjälp?
Om du behöver hjälp med Heatit Z-Wave Plus ställ en fråga nedan och andra användare kommer att svara dig
Termostat Heatit Manualer
19 Augusti 2025
16 Augusti 2025
15 Augusti 2025
4 Januari 2025
26 September 2024
26 September 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
Termostat Manualer
- Kidde
- Enda
- Boneco
- Tado
- Emerson
- Devi
- Ambiano
- Sygonix
- Vemer
- Avidsen
- Nest
- Bosch
- Extraflame
- Mueller
- Maico
Nyaste Termostat Manualer
13 Oktober 2025
12 Oktober 2025
12 Oktober 2025
5 Oktober 2025
2 Oktober 2025
2 Oktober 2025
29 September 2025
28 September 2025
28 September 2025
28 September 2025