Hifonics BRUTUS BE35-2100.1D Bruksanvisning
Sidor 2 Engels mottagare
Läs bruksanvisningen för Hifonics BRUTUS BE35-2100.1D gratis online eller ladda ner PDF:en. 17 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Power cable size
and fusing
It is critical to use the proper power
and ground cable. Select the size
listed here for your amplier model.
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
Be sure to use the proper fuse size
for each model. Some models require
an external fuse.
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplier to
a secure surface. Do not mount
the amplier upside down.
Attach the chassis ground
cable to the amplier
negative terminal. It is
important to make sure this
connection is very tight.
Bare metal
Attach the main power cable
to the amplier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
wire to the amplier remote
output of the source unit.
Connect the RCA cables to
the INPUT connectors. The
OUTPUT can be used to
provide input for a second
amplier.
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
Connect the speaker cables to
the speaker output connectors.
Follow the diagram below
that best ts your speaker
conguration.
The chassis ground connection
is critical to the performance
of the amplier. Choose a
location that is close to the
amplier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Disconnect
negative battery
terminal
Run Cables
Mount Amplier
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Signal Input
Connection
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Speaker
Connections
Chassis Ground
Be prepared to disarm your vehicle’s alarm and
to enter your radio / source unit code.
Stereo
Installation
Before you start
Monoblock single woofermultiple woofersMonoblock
Bridged
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
1
2
3
5
7
6
8
11
12
104
Turn the LEVEL control completely
counter-clockwise to minimum.
Level Control
9
6V 0.2V
INPUT
LEVEL
Model Fuse Size Cable Size
BE35-500.4
BE35 800.4
BE35 1200.1D
BE35 1700.1D
BE35 2100.1D
BE35 2500.1D
BE35 5000.5
2x25A ATC
2x35A ATC
1 x 80A Maxi
2 x 70A Maxi
External 200A
External 250A
External 100A
4ga
4ga
4ga
2ga
2ga
0ga
0ga
Produktspecifikationer
| Varumärke: | Hifonics |
| Kategori: | mottagare |
| Modell: | BRUTUS BE35-2100.1D |
Behöver du hjälp?
Om du behöver hjälp med Hifonics BRUTUS BE35-2100.1D ställ en fråga nedan och andra användare kommer att svara dig
mottagare Hifonics Manualer
Hifonics ZEUS ZG-1200.4 Bruksanvisning Hifonics NXi4002 Bruksanvisning Hifonics ZEUS ZG-1200.1D Bruksanvisning Hifonics Zeus Power ZXR900/4 Bruksanvisning Hifonics Thor TPS-A600.5 Bruksanvisning Hifonics ZRX Zeus Bruksanvisning Hifonics VXi9404 Bruksanvisning Hifonics Brutus BRX Bruksanvisning
Alla Hifonics mottagare manualer
Populära i mottagare
Hifonics HAC-3000.1D Bruksanvisning Hifonics Pluto II Bruksanvisning Hifonics Zeus Extreme ZXT3000/1 Bruksanvisning
mottagare Manualer
Nyaste mottagare Manualer
S.M.S.L DA100 Bruksanvisning PowerBass XL-355DM Bruksanvisning Sencor SDB 525T SENIOR Bruksanvisning Crown CTD-8125 Bruksanvisning RCF KPS 164 Bruksanvisning Pure Acoustics AV-4020 Bruksanvisning Crown CTD-4125 Bruksanvisning Crown CTD-2125 Bruksanvisning Christie CDA7.5 Bruksanvisning Christie CDA5 Bruksanvisning