Honeywell RTH111 Bruksanvisning
Läs gratis den bruksanvisning för Honeywell RTH111 (9 sidor) i kategorin Termostat. Guiden har ansetts hjälpsam av 7 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 4 recensioner. Har du en fråga om Honeywell RTH111 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/9
RTH111 69-2061EFS 1/-01 11/09 8
Use the System switch to place the system in one of the following
modes.
•Cool: System is in Cooling mode.
•Off: System is off.
•Heat: System is in Heating mode.
CAUTION: EQUIPMENT DAMAGE HAZARD
Do not use Cooling mode when the outdoor temperature
is below 50 °F (10 °C).
Use the Fan switch to select the fan operation.
•Auto: The fan runs only when heating or cooling is actually taking
place (commonly used setting).
•On: The fan runs continuously. Use this setting for improved air
circulation or for more efficient air cleaning.
Press the S or T button once to display the setpoint temperature.
Press either button more than once to change the setpoint.
The ambient (measured) temperature is normally displayed. To view
the setpoint temperature, press either of the temperature adjustment
buttons once. The setpoint temperature will appear for five seconds.
Your thermostat has a feature that helps prevent damage to the
compressor of your air conditioning system. Because damage can
occur if the compressor is restarted too soon after shutdown, this
feature forces the compressor to wait five minutes before restarting.
During the wait time, the message Cool On flashes on the screen.
When the safe wait time has elapsed, the message stops flashing
and the compressor turns on.
Set the System switch to Off before removing the
batteries. Otherwise, the heating/cooling system could
remain activated even when batteries are removed.
Install two fresh AAA batteries when the low-battery icon flashes on
the screen. The icon appears for 60 days before the batteries are
depleted. Replace batteries once a year, or when you will be away for
more than a month.
The settings are stored in non-volatile (permanent) memory and are
thus saved when the thermostat is without batteries.
n
n
n
nn 1.
System switch
Fan switch
Temperature
adjustment buttons
1 When Cool On is flashing, this means the compressor protection is engaged (see
section 1.6).
Temperature
System status
• Cool On: Cooling is
activated. 1
• Heat On: Heating is
activated.
Low-battery warning
Setpoint indicator
Appears when the
setpoint temperature
is displayed.
o
o
o
oo 2.
p
p
p
pp 3.
Screen is blank. • Ensure two fresh AAA alkaline batteries are
correctly installed.
Temperature settings
cannot be changed.
• The System switch is off.
• You are setting the temperatures outside
their allowable ranges:
• Heat: 40 °F to 90 °F (4.5 °C to 32 °C).
• Cool: 50 °F to 99 °F (10 °C to 37 °C).
Cool On is flashing. • The compressor protection delay has been
activated. Cooling will not be activated until
the delay ends (maximum of five minutes).
HI appears on the
screen.
• The ambient (measured) temperature is
above 122 °F (50 °C).
LO appears on the
screen.
• The ambient (measured) temperature is
below 32 °F (0 °C).
E1 appears on the
screen.
• The temperature sensor circuit is opened.
Replace the thermostat.
E2 appears on the
screen.
• The temperature sensor circuit is shorted.
Replace the thermostat.
69-2061EFS-01
Produktspecifikationer
| Varumärke: | Honeywell |
| Kategori: | Termostat |
| Modell: | RTH111 |
Behöver du hjälp?
Om du behöver hjälp med Honeywell RTH111 ställ en fråga nedan och andra användare kommer att svara dig
Termostat Honeywell Manualer
29 Juni 2025
28 Juni 2025
28 Juni 2025
3 April 2025
11 Mars 2025
6 Februari 2025
28 Januari 2025
16 Januari 2025
Termostat Manualer
- Eliwell
- IR-V
- AWB
- Fenix
- Mikoterm
- Bosch
- Elgato
- THERMAFLEX
- Elro
- TrickleStar
- Max
- Extraflame
- Mitsubishi
- Sinustec
- Viessmann
Nyaste Termostat Manualer
13 Oktober 2025
12 Oktober 2025
12 Oktober 2025
5 Oktober 2025
2 Oktober 2025
2 Oktober 2025
29 September 2025
28 September 2025
28 September 2025
28 September 2025