Honeywell RTH1120 Bruksanvisning
Läs gratis den bruksanvisning för Honeywell RTH1120 (8 sidor) i kategorin Termostat. Guiden har ansetts hjälpsam av 4 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 2.5 recensioner. Har du en fråga om Honeywell RTH1120 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/8
RTH1120 69-1875EF 22/2/06 1/4
The RTH110B non-programmable thermostat can be used to con-
trol:
• a gas, fuel oil or electric furnace - 2 or 3 wires
• a central air conditioner - 2 or 3 wires
• a hot water system with or without pump - 2 wires
• a millivolt system - 2 wires
• a central heating and cooling system - 4 or 5 wires
Note: This thermostat is not compatible with heat pumps or multi-
stage systems.
Features
• System operating mode selection: heat, cool or off
• Fan operating mode selection: automatic or on (continuous)
• Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
• Temperature display in °F or °C
• Backlit display
• Battery replacement indicator
• Interchangeable faceplates (titanium, charcoal & taupe)
2.1 Removing the Old Thermostat
IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.
nRemove the old thermostat to access the wires.
Attention: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
oIdentify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.
pIf necessary, strip the end of each wire (maximum of 1/4 inch).
qWrap the wires around a pencil to prevent
them from falling into the wall.
rIf the hole in the wall is too big, insulate it
using a non-flammable material in order
to avoid air draughts behind the thermo-
stat.
2.2 Installing the New Baseplate
For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.
nRemove the thermostat faceplate.
oLoosen the locking screw to separate the thermostat from its
baseplate (the screw cannot be completely removed).
pTilt the thermostat upwards.
qMark and bore the appropriate mounting holes (using a 3/16”
drill bit) or use the existing holes. Insert the plastic anchors.
rPass the wires through the opening of the baseplate and fix the
baseplate to the wall using the screws provided.
2.3 Connecting the Thermostat
Refer to the following table for matching the wire labels with the
thermostat terminals.
Note: Do not connect wires identified as C, X or B. Wrap the bare
end of these wires with electrical tape.
Important: The red jumper wire between Rh and Rc terminals must
be removed in a 5-wire installation.
1. Introduction
2. Installation
RTH1120
Non-programmable Electronic Thermostat
Installation and User Guide
Display Adjustment
buttons
System operating
mode selector Fan operating
mode selector
Backlight
button
RTH2520 terminals Description Wire labels
Rh Heating power supply Rh, R, 4, V
Rc Cooling power supply Rc, R
W Heating signal W, W1, H
Y Cooling signal Y, Y1, M
GFan G, F
Produktspecifikationer
| Varumärke: | Honeywell |
| Kategori: | Termostat |
| Modell: | RTH1120 |
Behöver du hjälp?
Om du behöver hjälp med Honeywell RTH1120 ställ en fråga nedan och andra användare kommer att svara dig
Termostat Honeywell Manualer
29 Juni 2025
28 Juni 2025
28 Juni 2025
3 April 2025
11 Mars 2025
6 Februari 2025
28 Januari 2025
16 Januari 2025
Termostat Manualer
- IMIT
- Watts
- Truma
- De Dietrich
- Ferguson
- Energenie
- Itho
- Maginon
- EVE
- HomeMatic
- Radson
- Tellur
- Elco
- Lowes
- Plieger
Nyaste Termostat Manualer
13 Oktober 2025
12 Oktober 2025
12 Oktober 2025
5 Oktober 2025
2 Oktober 2025
2 Oktober 2025
29 September 2025
28 September 2025
28 September 2025
28 September 2025