Honeywell RTH230B Bruksanvisning
Läs gratis den bruksanvisning för Honeywell RTH230B (4 sidor) i kategorin Termostat. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 3.8 stjärnor baserat på 2 recensioner. Har du en fråga om Honeywell RTH230B eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
• a gas, fuel oil or electric furnace - 2 or 3 wires
• a central air conditioner - 2 or 3 wires
• a hot water system with or without pump - 2 wires
• a millivolt system - 2 wires
• a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
• System operating mode selection: heat, cool or off
• Fan operating mode selection: automatic or on (continuous)
• Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
• Temperature display in °F or °C
• Battery replacement indicator
• 5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
• Filter replacement indicator
IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.
nRemove the old thermostat to access the wires.
Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
oIdentify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.
pIf necessary, strip the end of each wire (maximum of 1/4 inch).
qWrap the wires around a pencil to prevent
them from falling into the wall.
rIf the hole in the wall is too big, insulate it
using a non-flammable material in order to
avoid air draughts behind the thermostat.
For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.
nRemove the thermostat faceplate.
oLoosen the locking screw to separate the thermostat from its
baseplate (the screw cannot be completely removed).
pTilt the thermostat upwards.
qMark and bore the appropriate mounting holes (or use the
existing holes). Insert the plastic anchors.
rPass the wires through the opening of the baseplate and fix the
baseplate to the wall using the screws provided.
The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.
Display Adjustment
buttons
System operating
mode selector Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
G Fan
Produktspecifikationer
| Varumärke: | Honeywell |
| Kategori: | Termostat |
| Modell: | RTH230B |
Behöver du hjälp?
Om du behöver hjälp med Honeywell RTH230B ställ en fråga nedan och andra användare kommer att svara dig
Termostat Honeywell Manualer
29 Juni 2025
28 Juni 2025
28 Juni 2025
3 April 2025
11 Mars 2025
6 Februari 2025
28 Januari 2025
16 Januari 2025
Termostat Manualer
- Elektrobock
- Nobo
- UPM
- Tellur
- Drayton Erie
- Mikoterm
- Schwaiger
- SPC
- Oregon Scientific
- Schneider
- Seitron
- H-Tronic
- Netatmo
- Fibaro
- Itho
Nyaste Termostat Manualer
13 Oktober 2025
12 Oktober 2025
12 Oktober 2025
5 Oktober 2025
2 Oktober 2025
2 Oktober 2025
29 September 2025
28 September 2025
28 September 2025
28 September 2025