Roland SO-DA4 Bruksanvisning
Roland
ej kategoriserat
SO-DA4
Läs gratis den bruksanvisning för Roland SO-DA4 (4 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 28 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 14.5 recensioner. Har du en fråga om Roland SO-DA4 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
1
SI-AD4 / SO-DA4 Installation Manual
This guide describes how to install SI-AD4 (input) and SO-DA4 (output) modules in your S-4000S.
Before you attempt installation, please read this document carefully.
© 2005 Roland Corporation
All rights reserved. No part of this publication may be reproduced in any form without the written permission of
ROLAND CORPORATION.
When installing or detaching the SI-AD4 or SO-DA4, be sure to consult your RSS Authorized Service Center.
After installing the SI-AD4 or SO-DA4, please be sure to return this document to the purchaser.
• Always turn the unit off and unplug the AC plug before attempting installation of the
SI-AD4 or SO-DA4.
• Install only the specified option. Remove only the specified screws.
• To avoid the risk of damage to internal components that can be caused by static electricity,
please carefully observe the following whenever you handle the board.
❍
Before you touch the board, always first grasp a metal object (such as a water pipe), so
you are sure that any static electricity you might have been carrying has been
discharged.
❍
When handling the board, grasp it only by its edges. Avoid touching any of the
electronic components.
❍
Save the bag in which the board was originally shipped, and put the board back into it
whenever you need to store or transport it.
• Do not touch any of the printed circuit pathways.
• Never use excessive force when installing a circuit board. If it doesn’t fit properly on the
first attempt, remove the board and try again.
• When the SI-AD4 or SO-DA4 installation is complete, double-check your work.
• Use a Philips screwdriver of the appropriate size to avoid damaging the screw heads (a
number of 2 screwdriver).
• Turn the screwdriver counter-clockwise to loosen the screws-turn it clockwise to tighten
them.
• Be careful not to let the screws drop inside the each unit.
• Never leave a module uninstalled. Cover any unused slots with optional S-BP blank panels.
• Be careful not to cut your hand on the edge of the circuit board or the opening edge while
removing the S-BP.
For the Purchaser — Please Read
For the Installer (Service Technician) — Please Read
Cautions When Installing the SI-AD4 or SO-DA4
tightenloosen
* 0 4 2 3 2 8 3 4 - 0 3 *
04232834 08-03-3N
Produktspecifikationer
| Varumärke: | Roland |
| Kategori: | ej kategoriserat |
| Modell: | SO-DA4 |
Behöver du hjälp?
Om du behöver hjälp med Roland SO-DA4 ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat Roland Manualer
30 September 2025
31 Augusti 2025
31 Augusti 2025
31 Augusti 2025
31 Augusti 2025
19 Augusti 2025
19 Augusti 2025
19 Augusti 2025
19 Augusti 2025
19 Augusti 2025
ej kategoriserat Manualer
- YoLink
- AJA
- PXN
- Spracht
- Thermaltake
- Iiyama
- T.akustik
- Belkin
- Spectrasonics
- Valeo
- Graef
- Terratec
- Roger Schult
- Skaarhoj
- Vivo
Nyaste ej kategoriserat Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025