StarTech.com PEX4S953 Bruksanvisning
StarTech.com
Inte kategoriserad
PEX4S953
Läs gratis den bruksanvisning för StarTech.com PEX4S953 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 15 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 8 recensioner. Har du en fråga om StarTech.com PEX4S953 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: October 31, 2019
Product Diagram (PEX4S953 and PEX4S953LP)
Port Function
1Break-out Cable Port
• Connect the to connect 4-Port DB9 Break-out Cable
up to 4 Serial Devices
2Stand-os
• Attach the to the Bracket PCI Express Serial Card
• Secure the to the 4-Port DB9 Break-out Cable
Break-out Cable Port
3Bracket • Attach the to the PCI Express Serial Card Computer
4
PCI Express Bus
Connector
• Connect the to the PCI Express Serial Card
Computer Motherboard
5Jumpers
• Congure the individual power Serial Connector
settings
6LP4 Power Connector • Used to connect an LP4 Power Source
4-Port PCI Express RS232 Serial Card - 16950 UART
Requirements
For the latest requirements please visit:
www.startech.com/PEX4S953 www.startech.com/PEX4S953LP. - or -
• PCIe Slot
• Needle-Nose Pliers
• (Optional) LP4 Power Source
Installation
WARNING!
PCI Express Serial Cards can be severely damaged by static electricity. Make sure
that you are properly grounded before you open the or touch the Computer Case
PCI Express Serial Card Anti-Static Strap . You should wear an when you install
any computer component. If an isn’t available, discharge any Anti-Static Strap
built-up static electricity by touching a large for several Grounded Metal Surface
seconds. Only handle the by its edges and don’t touch PCI Express Serial Card
the gold connectors.
Jumper Conguration
Note: This is specially designed to allow for power output PCI Express Serial Card
from the ninth pin of the for that support power Serial Connector(s) Serial Devices
over serial. conguration is a requirement when connecting Jumper Serial Devices
that require power through a .Serial Connector
The can be moved into one of three dierent positions in order to set the Jumper
power output voltage for the . The default setting for the Serial Connector Jumpers
is , no power. The must be connected after conguring theRI LP4 Power Connector
Jumper 5V 12V Jumper to or of power. To congure the , complete the following:
1. Ensure the isComputer Power O.
2. Locate the for and carefully remove the . Lift the Jumper Port One Jumper Jumper
straight up and o of the .PCI Express Serial Card
Notes: The is located on the right hand side, labeled as on the Jumper Port 1
. Printed Circuit Board
Always hold the by the edges.Card
3. Determine the power setting that is required for .Port One
4. Position the over the set of that correspond with the desired Jumper Pins Serial
Connector Power Setting Jumper. See to determine where the Figure 1 should be
positioned.
1
4
6
3
5
2
Produktspecifikationer
| Varumärke: | StarTech.com |
| Kategori: | Inte kategoriserad |
| Modell: | PEX4S953 |
Behöver du hjälp?
Om du behöver hjälp med StarTech.com PEX4S953 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad StarTech.com Manualer
18 Mars 2025
18 Mars 2025
3 Januari 2025
2 Januari 2025
2 Januari 2025
2 Januari 2025
2 Januari 2025
2 Januari 2025
2 Januari 2025
2 Januari 2025
Inte kategoriserad Manualer
- Pioneer
- Scandomestic
- We-Vibe
- Cambo
- Thetford
- Leba
- Trigano
- Novus
- Coxreels
- Vestel
- Viomi
- Mestic
- Chrome-Q
- Dodow
- Rode
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025