Vaddio RoboTRAK Bruksanvisning

Vaddio övervakningskamera RoboTRAK

Läs gratis den bruksanvisning för Vaddio RoboTRAK (2 sidor) i kategorin övervakningskamera. Guiden har ansetts hjälpsam av 24 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 12.5 recensioner. Har du en fråga om Vaddio RoboTRAK eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

Drop-Down Mount Accessory for RoboTRAK™

UNPACKING:

Carefully remove the product and all of the parts from the

packaging. Unpack and identify the following parts (cameras not

included):

➊

One (1) 1-14 Hex Nut (jamb nut)1.5” across by .375” Tall

➋

One (1) Offset Pipe with 1-14 Threads

➌

One (1) Mounting Flange (5” diameter)

➍

One (1) Tile Support Brace

➎

One (1) Large 5” Washer

➏

Two (2) 1-14 Hex Nut, 1.5” across x .547” Tall (one used as

fastener and the other as a top jamb nut)

(Cameras are not included)

Step 1: For suspended ceiling installations, mark a position in the center of

a ceiling tile where the ceiling mount is to be placed. The hole must be

positioned at the center of the ceiling tile lengthwise for 2’ x 4’ ceiling tiles to

line up with the tile support brace. Use the tile support brace as a template.

The tile support brace is meant to span the tile and distribute the weight into

the grid.

For drywall ceiling installations, mark a position in the ceiling while making

sure that there are no obstructions (structural supports, electrical, etc.) in the

area above the mount.

Step 2: Drill or cut a 1” (25.4mm) diameter hole in the tile or drywall at the

point where you marked the hole. For suspended ceiling installations, place

the support brace on the top of the ceiling tile and align the hole with the tile

support brace. There are six holes drilled in the support brace for attaching

to the building structure where regional codes require this additional support.

For drywall ceiling installations, place the Mounting Flange over the 1” hole,

and mark the four locations in the flange to install appropriate hardware (wall

anchors) for mounting the flange to the ceiling.

Step 3: Thread the 1.5” x .375” Jam Nut onto the bottom of the pipe (the side with the shorter threads), then thread the

Camera Platform all the way onto the pipe. Back the Camera Platform off the pipe (one rotation or less) until the back of the

Camera Platform aligns with the cable pass-thru. Carefully tighten the 1.5” x .375” Jam Nut down onto the threaded nut of the

Camera Platform.

Step 4: Thread the painted 5” flange onto the other end of the pipe.

Step 5: For suspended ceiling installations, slide the pipe with 5” flange end through the hole in the ceiling tile. From one tile

over, place the 5” washer onto the threaded pipe, and screw the first 1.5” x 5.5” hex nut onto the pipe thread and tighten the

hex nut down, then thread the second hex nut (jam nut) onto the top of the pipe and tighten it. Carefully feed the Cat-5 cabling

through the pipe and the cable pass-thru at the back of the camera mount. There are six (6) mounting points on the Tile

Support Brace to allow the integrator to tie the assembly to the structure for safety in seismic prone areas.

For drywall ceiling installations, once the appropriate mounting hardware for the flange is installed, carefully pull the Cat-5

cabling through the 1” hole in your drywall ceiling. Thread the cabling through the pipe, and pull it through the cable pass thru

at the back of the camera platform. Place the flange on the ceiling and tighten the screws down onto the mounting hardware.

Step 6: Place your camera onto the mount and secure it to the camera platform using the supplied black screw(s). Connect

the Cat. 5 cabling to the back of the camera and carefully feed excess Cat. 5 cabling back into the ceiling. Use the ¼” - 20

x .375: screws for the RoboSHOT cameras.

Installation and User Guide

➊

➏

➎

➍

➌

➋

Produktspecifikationer

Varumärke:	Vaddio
Kategori:	övervakningskamera
Modell:	RoboTRAK
Produkttyp:	Spårningssystem
Vikt:	1360 g
Bredd:	155 mm
Djup:	145 mm
Höjd:	163 mm
Infraröd våglängd:	850 nm
Bildsensorstorlek:	- "
Gränssnitt:	RJ-45
Antal personer:	- personer
USB-laddare medföljer:	Ja
Väggmonteringssats:	Ja
Horisontell rotationsvinkel:	-90 - 90 °
Antal förinställda positioner:	10
Produktens färg:	Svart, silver
Monteringsbar på väggen:	Ja
Datahastighet för Ethernet-LAN:	10, 100 Mbit/s
Temperatur vid drift:	0 - 24 ° C
Temperaturintervall (förvaring):	-5 - 60 ° C
Intervall för relativ operativ luftfuktighet:	15 - 80 %
Fuktighet (förvaring):	20 - 80 %
Kabel inkluderad:	AC, USB
Placeringar som kan användas:	Vägg
Anslutningsteknologi:	Kabel
Nätverksansluten (Ethernet):	Ja
Likströmsingång:	Ja
Strömkälla av typen:	DC
Brand kompatibilitet:	Vaddio
Ström:	3 A
Webbaserad adminstraion:	Ja
Manual:	Ja
Harmonized System (HS)-kod:	85299097
PoE-adapter ingår:	Ja
Ingående ström:	3 A
Antal Power over Ethernet plus (PoE +)-portar:	1
Kamera inkluderad:	Ja
Drifttid för batteri:	40 h
Likströmsdriftspänning:	12 V
Kamerans mått (BxDxH):	155 x 145 x 163 mm
Fjärrkontrollsgränssnitt:	IR trådlös
Kabel standard:	Cat5e
Kamerans kabellängd (max):	15.2 m
Spårmarkeringens vikt:	91 g
Spårmarkeringens mått (BxDxH):	51 x 25 x 51 mm
Laddningstid för spårmarkering:	4 h
Spårmarkering inkluderad:	Ja
Typ av spårmarkering:	Infraröd (IR)
Arbetsområde för infraröd kamera:	3.7 - 15.2 m
Förskjutningsvinkel:	20 °