Varo MOTSA10EL Bruksanvisning
Läs gratis den bruksanvisning för Varo MOTSA10EL (2 sidor) i kategorin Valv. Guiden har ansetts hjälpsam av 29 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 15 recensioner. Har du en fråga om Varo MOTSA10EL eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
MOTSA10EL, 12EL, 15EL & 19EL EN
Copyright © 2012 VARO www.varo.com NV Page | 1
OPERATION INSTRUCTIO NS
CAUTION: Do not keep the keys in the safe.
1 OPEN THE SAFE FOR THE FIRST TIME
To open the safe for the rst time, remove the small plastic cover on the front panel, insert the
key into the lock and turn it counter-clockwise, at the same time, turn the knob clockwise and
open the door.
2 INSTALLING THE BATTERIES.
The safe requires 4× size ‘AA’ (1.5V/R06) batteries. Remove the battery cover and install the
batteries into the compartment. Ensuring the batteries are fitted with the correct corresponding
polarity. The display will scan the status of the electronic lock system automatically. If it is in
order, the display will show ‘good’.
3 OPENING THE SAFE AFTER INSTALLING BATTERIES
To open the door of the safe, press the button ‘START’, the display on the panel will show ‘----
----’, then input one of the two sets of factory-preset codes:
0,0,0,0 (user code) or 8,8,8,8 (master code) immediately and conrm by pressing the button
‘START’. You will hear a musical sound with the display showing ‘OPEN’ and open the safe
using the knob within approximately 4 seconds.
4 PROGRAMMING THE CODE
NOTICE: The safe can be programmed with two sets of codes. For your safety, after
opening the safe and installing the batteries, you should program two sets of your new
codes to take the place of two sets of factory-preset codes.
4.1 Programming the user code
A. With the door of the safe open, press the red button (located on the inside of the door near
the hinge) and the display will show ‘SET CodE’.
B. Now press from 3 to 8 numbers that you wish to use as a new user code, and conrm by
pressing the button ‘START’. After hearing a musical sound, the display will show ‘IN’ and your
inputting numbers. It means that the new user code is conrmed.
4.2 Programming the master code
A. Press the red button then press the button ‘START’. The display will show ‘oLd CodE’.
B. Now input the original master code (factory preset code: 8,8,8,8) and press the button
‘START’. The display will show ‘SET’. Now press from 3 to 8 numbers that you wish to use as
a new master code, and conrm by pressing the button ‘START’. The display will show ‘rE-
InPUT’.
C. Now enter your inputting numbers again and conrm by pressing the button ‘START’. After
hearing a musical sound, the display will show ‘IN’ and your inputting numbers. It means that
the new master code is conrmed.
If you or an intruder uses the incorrect group of numbers, you will hear a beep with the display
showing ‘Error’ and it will not open. If the incorrect combination code is used 4 times
consecutively, the display will show ‘Error’, the buzzer will sound for approximately 3 minutes.
The correct code cannot be entered until after this 3 minutes delay. The override key can
however be used to open the door during this three minutes. If the key is used to open the
door, the buzzer can be cleared by pressing the red button.
If you do not want the display to show your codes or numbers when you open the safe, just
press the button ‘START’ twice at the first time of pressing and other steps are the same.
Produktspecifikationer
| Varumärke: | Varo |
| Kategori: | Valv |
| Modell: | MOTSA10EL |
Behöver du hjälp?
Om du behöver hjälp med Varo MOTSA10EL ställ en fråga nedan och andra användare kommer att svara dig
Valv Varo Manualer
15 September 2024
14 September 2024
23 Augusti 2024
20 Augusti 2024
12 Augusti 2024
31 Juli 2024
29 Juli 2024
Valv Manualer
- SMC
- EasySafe
- ROMA
- First Alert
- CAWI
- Suncast
- Stamony
- Abus
- Royal Sovereign
- Perel
- Burg-Wachter
- M-Locks
- Oxloc
- Kreator-Varo
- NOFIRE
Nyaste Valv Manualer
1 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
27 Mars 2025
1 Februari 2025
9 Januari 2025
7 Januari 2025
1 Januari 2025