Velleman KNS4 Bruksanvisning
Läs gratis den bruksanvisning för Velleman KNS4 (7 sidor) i kategorin Leksaker. Guiden har ansetts hjälpsam av 38 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 19.5 recensioner. Har du en fråga om Velleman KNS4 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/7
KNS4 VELLEMAN 1
KNS4 – COPTERMECH
1. Introduction & Characteristics
Thank you for buying the KNS4 ! Read this manual carefully before bringing the device into use.
• Familiarise yourself with the operation of transmissions steered through gears or pulleys.
• Easy to build, no glue or soldering required.
• Dislodge the pre-cut pieces when you need them and not before. Sand the jagged edges before use (sandpaper
included)
• The kit is powered by 2 AA-batteries (not included).
The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a
battery holder and all necessary parts.
Note that the figures with the assembly instructions can be found in the second folder “KNS4 – Figures”!!!
2. Parts List
Part n° Quant. Description Part n° Quant. Description
1 1 motor holder
12 2 fixing plate
2 1 battery holder 13 3 PVC tube (1.5 x 15mm)
3 1 motor with wire 14 3 metal shaft (2 x 90mm)
4 15
1 slide switch with wire 3 metal shaft (2 x 70mm)
5 1 plastic tube (L : 15cm) 16 1 belt (black) (126 x 1mm)
6 17 1 metal shaft (2 x 40mm) 1 rubber band (35mm, red)
7 1 pinion gear 18 4 rubber band (40mm red)
8 19 1 face gear 36T/14T (white) 7 fixing plate (L-shaped)
9 20 2 pulley 19.5 x 2mm (blue) 15 nylon pad
10 8 pulley 15 x 2mm (yellow) 21
11 nylon pad
11 22 2 pulley 24 x 2mm (white) 26 self-tapping screw
3. Prepunched Boards (see “KNS4 – Figures
”
)
4. Assembly (see also “KNS4 – Figures
”
)
Fig. 4 : Insert part n°20 in the hole on board n°2 and mount the motor holder according to fig. 4.
Fig. 5 : Insert part n°20 (x 8) in boards n°1 & 4. Insert part n°7 between boards 1 & 4. Insert 2 x part n°15 in board
n°4 and through the pulley (part n°10). The metal shafts come out the other side of board n°1. Remember
to put the rubber bands (parts n°18 & 16) on the pulley before inserting the metal shaft. Another part n°15
goes through boards n°1 & 4.
Fig. 6 : Cut part n°5 to precisely 32mm. Insert part n°20 in board n°5 first, then put metal shaft n°14 through board
n°5. Mount part n°5 & 8 according to figure 6. Attach board n°5 to boards n°1 & 4 with part n°19.
Produktspecifikationer
| Varumärke: | Velleman |
| Kategori: | Leksaker |
| Modell: | KNS4 |
Behöver du hjälp?
Om du behöver hjälp med Velleman KNS4 ställ en fråga nedan och andra användare kommer att svara dig
Leksaker Velleman Manualer
9 December 2024
6 Oktober 2024
2 Oktober 2024
27 September 2024
10 Augusti 2024
24 Juli 2024
Leksaker Manualer
- BML
- Easypix
- Babymoov
- Sunnydaze Decor
- Classic World
- Webley
- Kindercraft
- Style Me Up
- Denver
- Invento
- IKEA
- Viessmann
- Rolly Toys
- Kayoba
- Maxxmee
Nyaste Leksaker Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
8 April 2025