Velleman KNS5 Bruksanvisning


Läs gratis den bruksanvisning för Velleman KNS5 (7 sidor) i kategorin Leksaker. Guiden har ansetts hjälpsam av 35 personer och har ett genomsnittsbetyg på 3.9 stjärnor baserat på 18 recensioner. Har du en fråga om Velleman KNS5 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/7
KNS5 VELLEMAN 1
KNS5 – AUTOMECH
1. Introduction & Characteristics
Thank you for buying the KNS5 ! Read this manual carefully before bringing the KNS5 into use.
Familiarise yourself with the operation of transmissions steered through gears or pulleys.
Easy to build, no glue or soldering required.
Dislodge the pre-cut pieces when you need them and not before. Sand the jagged edges before use (sandpaper
included)
The kit is powered by 2 AA-batteries (not included).
The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a
battery holder and all necessary parts.
Note that the figures with the assembly instructions can be found in the second folder “KNS5 – Figures”!!!
2. Parts List
Part n° Quant. Description Part n° Quant. Description
1 1 motor holder 11 3 PVC tube (L=15mm)
2 1 battery holder 12 11 fixing plate (L-shaped)
3 1 motor with wire 13 4 nylon pad (Ø8mm)
4 14 1 slide switch with wire 1 belt (92 x 1mm)
5 15 2 metal shaft (2 x 60mm) 3 transmission belt # 16 (red)
6 16 2 metal shaft (2 x 70mm) 1 transmission belt # 18 (green)
7 3 roll (15 x 1.9mm, yellow) 17 4 nut M2
8 5 roll (19.5 x 1.9mm, yellow) 18 24 self-tapping screw (2 x 4mm)
9 8 nylon pad (6.6 x 4.8 x 2.1) 19 4 screw (2 x 8mm)
10 8 nylon pad (5.6 x 4.8 x 1.95) 20 4 washer
3. Prepunched Boards (see KNS5 – Figures
)
4. Assembly (see also KNS5 – Figures
)
Fig. 3 : Screw part n°12 to boards 4 & 5, then fix these boards to board 1.
Fig. 4 : Insert the motor (part n°3) in the motor holder (part n°1) and screw the battery holder (part n°2) to the back
of board 2. Screw the switch to the back of board 1. Refer to the wiring diagram (fig. 10) when connecting
the switch, the motor and the battery holder with each other.
Fig. 5 : Screw part n°12 to parts 2 & 3., then fix them to board n°1.
Fig. 7 : Use part n°12 to fix boards n°10 & 12 to board n°7, then use part n°12 to fix board n°11 to board n°6 (not
to board 7).
Fig. 8 : Assemble all pulleys, shafts and wheels according to figure 8.


Produktspecifikationer

Varumärke: Velleman
Kategori: Leksaker
Modell: KNS5

Behöver du hjälp?

Om du behöver hjälp med Velleman KNS5 ställ en fråga nedan och andra användare kommer att svara dig