Velleman KNS8 Bruksanvisning
Läs gratis den bruksanvisning för Velleman KNS8 (8 sidor) i kategorin Leksaker. Guiden har ansetts hjälpsam av 41 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 21 recensioner. Har du en fråga om Velleman KNS8 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/8
KNS8 VELLEMAN 1
KNS8 – MECHANICAL SKELETON
1. Introduction & Characteristics
Thank you for buying the KNS8 ! Read this manual carefully before bringing the KNS8 into use.
• Build a gearbox and learn how automatic transmissions and motors work.
• Easy to build, no glue or soldering required.
• Dislodge the pre-cut pieces when you need them and not before. Sand the jagged edges before use (sandpaper
included)
• The kit is powered by 2 AA-batteries (not included).
The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a
battery holder and all necessary parts.
Note that the figures with the assembly instructions can be found in the second folder “KNS8 – Figures”!!!
2. Parts List (see also KNS8 – Figures)
Part n° Quant. Description Part n° Quant. Description
1 1 gearbox 18 6 nylon nut M3
2 1 motor 3Vdc 19 18 nut M2
3 1 battery holder 20 18 screw (2 x 8mm)
4 21 1 slide switch with wire 4 self-tapping screw (2 x 4mm)
5 22 1 metal shaft (2 x 40mm) 2 screw (3 x 14mm)
6 23 1 metal shaft (3 x 52mm) 2 screw (3 x 18mm)
7 1 pinion gear 8T 24 2 screw (3 x 22m)
8 25 1 face gear 36T/10T (white) 8 washer (3.2 x 10.0 x 0.5mm)
9 26 1 gear 40T/0T (white) 15 washer (2.6 x 6.0 x 0.5mm)
10 1 gear 40T/10T (red) 27 3 PVC tube (15mm)
11 1 gear 40T/10T (green) 28 10 nylon pad (Ø 8mm)
12 29 1 wire with terminal (yellow) 5 fixing plate (L-shaped)
13 30 1 wire with terminal (green) 4 nylon post (H : 3mm)
14 2 metal foot (U-shaped) 31 1 spring (L : 50mm)
15 32 2 nylon connector (N-shaped) 2 spring (L : 20mm)
16 2 nylon pad (5.6 x 4.8 x 1.95) 33 6 self-tapping screw (2 x 6mm)
17 2 nylon post (H : 6mm)
3. Prepunched Boards (see “KNS8 – Figures
”
)
4. Assembly (see also “KNS8 – Figures
”
)
Fig. 3 : The gears (n°9/10/11/8) should be placed to the left of the pinion gear. One N-shaped nylon connector
(n°15) should point downward and the other one upward. Insert the motor as depicted in the drawing. Note
that the protruding edge should point towards the metal case.
Fig. 4 : Identify boards 2 & 3. The screw opening in board 3 is located in the middle, while the one in board 2 lies
off to the left. Make sure board 1 is not upside-down.
Produktspecifikationer
| Varumärke: | Velleman |
| Kategori: | Leksaker |
| Modell: | KNS8 |
Behöver du hjälp?
Om du behöver hjälp med Velleman KNS8 ställ en fråga nedan och andra användare kommer att svara dig
Leksaker Velleman Manualer
9 December 2024
6 Oktober 2024
2 Oktober 2024
27 September 2024
10 Augusti 2024
24 Juli 2024
Leksaker Manualer
- Maxxmee
- Rainbow
- Propel
- Triumph Sports
- Snap Circuits
- King
- Rolly Toys
- Jobe
- Mattel
- ProSin
- DS
- Denver
- Joy-it
- Polly Pocket
- MOTA
Nyaste Leksaker Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
8 April 2025