Mount-It! MI-2758 Bruksanvisning
Mount-It!
Platt panelstöd
MI-2758
Läs gratis den bruksanvisning för Mount-It! MI-2758 (5 sidor) i kategorin Platt panelstöd. Guiden har ansetts hjälpsam av 17 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 9 recensioner. Har du en fråga om Mount-It! MI-2758 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/5
FREESTANDING DUAL MONITOR
ARM WITH HEIGHT ADJUSTMENT
MI-2758
Scan this QR code for
product information, videos,
and assembly assistance.
Thank you for choosing Mount-It
2
3
Mount-It!
Mount-It!
Mount and Accessories
Mounting Hardware
Stand Arm Bolt Bolt Hex Wrench Hex Wrench
Hand Knob
Horizontal Arm Decorative
Cover
VESA Plate Handle Stand Base
Missing Parts? Call us at (855) 925-5668 and we will ship replacement parts free of charge.
CHOKING HAZARD. Package includes small parts.
Not for children under 3 years. Adult supervision is required.
Check carefully to make sure there are no missing or defective parts. Some hardware provided may not
be used. Use the correct mounting hardware suitable for your installation.
DIMENSIONS & WEIGHT CAPACITY
Rated weight capacity
is 17.6lbs for each arm.
Caution:
Ensure all mounting
surfaces are capable
of holding the weight
of your mount.
DO NOT EXCEED
MAXIMUM LISTED
WEIGHT CAPACITY.
SERIOUS INJURY OR
PROPERTY DAMAGE
MAY OCCUR!
11.2”
0.2”
min12.4”~max18.3”
3”
3.9”
4.5”
min6.1”~max7.7”
12.2”
min5”~max6.6”
min1.2”~max1.8”
33.5”
4.5”
9.8”
3.9”
3”
max29.5”
5
4
• Connect the Stand Base (#F) to the bottom of the Stand Arm (#A) using the Bolts (#H) and tighten until
secure using the 4mm Hex Wrench (#J)
Connect the Base and Arm
Step 1
• Select the appropriate size mounting bolt (#M-A, M-B) and washer (#M-C) for your monitors mounting
holes and verify the length of the VESA bolt is not too long. If you are unsure of the correct bolt size for
your display refer to your monitor user manual or contact the monitor manufacturer for sizing information.
Attach the VESA plate to the back of each monitor using the selected bolts and washers in the orientation
shown here.
• Insert the Hand Knobs (#G) into the bolt holes
on the back of the VESA Plates.
Attach the VESA Plates to the Monitors
Step 3
Attach the Monitors to the Horizontal Arm
Step 4
1. Attach the Handle (#E) to the lower bolt holes on the stand arm using Bolts (#I) and tighten using Hex
Wrench (#K)
2. Attach the Horizontal Arm (#B) to the front of the stand arm using Bolts (#I) and tighten using Hex
Wrench (#K)
3. Place the Decorative Cover (#C) over the middle of the horizontal arm so that it fully covers the
installed bolts.
Assemble the Monitor Arm
Step 2
• Slide the brackets on the back of the VESA Plates onto the ends of the Horizontal Arm. Once the
monitors are in the desired positions fix them in place by tightening the hand knob installed in the
previous step 3.
• Once the VESA Plates are on the arm, install 1 each of the Bolts (#I) to the end of
each arm to prevent the monitor from being accidentally removed.
Caution: Keep a hand on the stand when mounting the monitors to prevent the stand from tipping.
Identical monitors should be used to prevent balance issues.
Produktspecifikationer
| Varumärke: | Mount-It! |
| Kategori: | Platt panelstöd |
| Modell: | MI-2758 |
Behöver du hjälp?
Om du behöver hjälp med Mount-It! MI-2758 ställ en fråga nedan och andra användare kommer att svara dig
Platt panelstöd Mount-It! Manualer
2 April 2025
2 April 2025
2 April 2025
22 Mars 2025
27 December 2024
27 December 2024
27 December 2024
27 December 2024
24 September 2024
24 September 2024
Platt panelstöd Manualer
- Nabo
- Multibrackets
- Abus
- Wentronic
- My Wall
- Zaor
- Luxor
- Heckler
- Marantz
- GPX
- Icy Box
- BenQ
- Ultimate
- LTN Technologies
- Kondator
Nyaste Platt panelstöd Manualer
8 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025