Mount-It! MI-3770 Bruksanvisning
Mount-It!
Inte kategoriserad
MI-3770
Läs gratis den bruksanvisning för Mount-It! MI-3770 (9 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 29 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 15 recensioner. Har du en fråga om Mount-It! MI-3770 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/9
TABLET FLOOR STAND WITH
DOCUMENT HOLDER
MI-3770B_G10
MI-3770W_G10
Please scan this QR code
to visit the product page.
Thank you for choosing Mount-It
2
3
Mount-It!
Mount-It!
Mount and Accessories
Anti-Theft Tablet Case
A (x1)
Column
B (x1)
Connector
C (x1)
Document Tray
Connector
D (x1)
Missing Parts? Call us at (855) 925-5668 and we will ship replacement parts free of charge.
CHOKING HAZARD. Package includes small parts.
Not for children under 3 years. Adult supervision is required.
Check carefully to make sure there are no missing or defective parts. Some hardware provided may not
be used. Use the correct mounting hardware suitable for your installation.
DIMENSIONS & WEIGHT CAPACITY
Rated weight capacity is 2.2lbs for
the mount.
Caution:
Ensure all mounting surfaces are
capable of holding the weight of
your mount.
DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY.
SERIOUS INJURY OR PROPERTY
DAMAGE MAY OCCUR!
1
2.2
43.1”
15.7”
2.4”
0.9”
9”
8.9”
11.8”
9.8”
13.3”
0.2”
1.7”
Rubber Pad
E (x4)
M8x20
M (x4)
Tablet Adapter 1
U1 (x1)
5mm Hex Wrench
X (x1)
Tablet Adapter 2
U2 (x1)
Tablet Adapter 3
U3 (x1)
Wrench
V (x1)
4mm Hex Wrench
W (x1)
Low Profile Base
N (x1)
Washer
O (x4)
M5
P (x4)
M5x12
Q (x4)
ST4.8x30
S (x4)
M4x12
R (x4)
Concrete
Anchor
T (x4)
Standing Base
F (x1)
Concrete
Anchor
I (x4)
Key
J (x1)
M4x6
K (x2)
Document Tray
G (x1)
ST6.3x55
H (x4)
Button Cover
Y (x1)
M5x6
L (x4)
5
4
• Peel the backing off the Rubber Pads (#E) and place them near each corner of the Standing Base (#F).
Place the pads on the bottom side which has the recessed indentations.
Standing Base Option
Step 2
Step 2a-1
• Attach the Column (#B) to the Standing
Base (#F) through the Base Connector (#D)
using Bolts (#M) as shown.
Attach the Base
Step 2a-2
• In the orientation shown here, slide the Document Tray Connector (#C) onto the Column (#B) from the
base and position it approximately halfway up the column. Tighten the bolts on the side of the connector
to secure it in place.
Install the Document Tray Connector
Step 1
B. Wood Surface Installation
• To secure the stand base to a wood surface use a 3/16” bit and drill holes to a depth of 2.2” and secure
the stand base using 2x Lag Screws (#H). Do not over tighten.
Note: Ensure the mounting surface is thick enough to accommodate the length of the Lag Screws.
• The stand may be placed directly on the floor for
use or can be secured following the instructions in
the next steps.
A. Positioning and Use
Step 2a-3 Location and Use Options
Produktspecifikationer
| Varumärke: | Mount-It! |
| Kategori: | Inte kategoriserad |
| Modell: | MI-3770 |
Behöver du hjälp?
Om du behöver hjälp med Mount-It! MI-3770 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Mount-It! Manualer
2 April 2025
29 Januari 2025
27 December 2024
27 December 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
Inte kategoriserad Manualer
- Valco Baby
- FIMI
- Nexa
- Jokari
- Mobli
- Weihrauch Sport
- Microsoft
- Milectric
- Eero
- Yamato
- Maxi-Cosi
- Jenn-Air
- Hive
- Praktica
- Brondi
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025