Mount-It! MI-3771 Bruksanvisning
Mount-It!
Inte kategoriserad
MI-3771
Läs gratis den bruksanvisning för Mount-It! MI-3771 (9 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 20 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 10.5 recensioner. Har du en fråga om Mount-It! MI-3771 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/9
TABLET COUNTERTOP STAND
MI-3771B_G10
MI-3771W_G10
Please scan this QR code
to visit the product page.
Thank you for choosing Mount-It
2
3
Mount-It!
Mount-It!
Mount and Accessories
Anti-Theft Tablet Case
A (x1)
Standing Base
B (x1)
Base
C (x1)
Rubber pad
D (x4)
Missing Parts? Call us at (855) 925-5668 and we will ship replacement parts free of charge.
CHOKING HAZARD. Package includes small parts.
Not for children under 3 years. Adult supervision is required.
Check carefully to make sure there are no missing or defective parts. Some hardware provided may not
be used. Use the correct mounting hardware suitable for your installation.
DIMENSIONS & WEIGHT CAPACITY
Rated weight capacity is 2.2lbs for
the mount.
Caution:
Ensure all mounting surfaces are
capable of holding the weight of
your mount.
DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY.
SERIOUS INJURY OR PROPERTY
DAMAGE MAY OCCUR!
1
2.2
11.9”
11.8”
0.9”
7.9”
13.3”
0.2”
1.7”
2.4”
8.9”
Base Connector
E (x1)
M8x45
Grommet Bolt
L (x1)
Tablet Adapter 1
T1 (x1)
5mm Hex Wrench
W (x1)
Button Cover
X (x1)
Tablet Adapter 2
T2 (x1)
Tablet Adapter 3
T3 (x1)
Wrench
U (x1)
4mm Hex Wrench
V (x1)
Grommet
Washer
M (x1)
Grommet
Washer
N (x4)
M5
O (x4)
M5x12
P (x4)
M4x12
Q (x4)
ST4.8x30
R (x4)
Concrete Anchor
S (x4)
ST6.3x55
F (x4)
M5x6
I (x4)
M8x20
J (x4)
Low Profile Base
K (x1)
Concrete Anchor
G (x4)
Key
H (x1)
5
4
• Peel the backing off the Rubber Pads (#D) and place them near each corner of the Standing Base (#C).
Place the pads on the bottom side which has the recessed indentations.
Standing Base Option
Step 1
Step 1a-1
• Attach the Column (#B) to the Standing Base (#C)
through the Base Connector (#E) using Bolts (#J) as
shown.
Attach the Base
Step 1a-2
• The stand may be placed directly on a countertop
or tabletop for use or can be secured following the
instructions in the next steps.
A. Countertop Use
Step 1a-3 Location and Use Options
B. Wood Surface Installation
• To secure the stand base to a wood surface use a 3/16” bit and drill holes to a depth of 2.2” and secure
the stand base using 2x Lag Screws (#F). Do not over tighten.
Note: Ensure the mounting surface is thick enough to accommodate the length of the Lag Screws.
C. Concrete Surface Installation
• To secure the stand base to a concrete surface, use a 3/8” Bit and drill holes to a depth of 2.4”. Clear
any dust and debris from the holes and insert 2x Concrete Anchors (#G). Secure the stand base using
2x Lag Screws (#F). Do not over tighten.
Note: Ensure the mounting surface is thick enough to accommodate the length of the Lag Screws.
Produktspecifikationer
| Varumärke: | Mount-It! |
| Kategori: | Inte kategoriserad |
| Modell: | MI-3771 |
Behöver du hjälp?
Om du behöver hjälp med Mount-It! MI-3771 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Mount-It! Manualer
2 April 2025
29 Januari 2025
27 December 2024
27 December 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
Inte kategoriserad Manualer
- Bruynzeel
- Weidmüller
- AS - Schwabe
- Testec
- Vipack
- Kisag
- Bushnell
- Wet Sounds
- Socket Mobile
- Active Era
- Casa Deco
- GMB Gaming
- Ikan
- Plustek
- Apc
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025