Salus AT10 Bruksanvisning
Läs gratis den bruksanvisning för Salus AT10 (2 sidor) i kategorin Termostat. Guiden har ansetts hjälpsam av 6 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 3.5 recensioner. Har du en fråga om Salus AT10 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
Operating and installation instructions
Features
- Pipe surface mounted thermostat with visible external scale
- Simple attachment with elastic tensioning band
- Simple operation with large hand dial
- Can be locked to set temperature
- Setting range from 30°C - 90°C
- Simple electrical connection with the generously sized cable clamps
Mounting
Press the pipe surface mounted thermostat firmly against the heating pipe and secure it with
the elastic tensioning band provided, so that the thermostat is directly abutting the pipe. (Any
isolation is to be removed at the installation site before securing the sensor.) Excess tensioning
band can be trimmed off.
Electrical connection
Open the thermostat by removing the dial (1) and loosening the large plastic screw (2). Remove
the housing cover. The 4 cable clamps which are now visible are to be wired as follows:
• Clamps C and 1 = opener
The thermostat opens under increasing temperature and closes in the case of sinking tem-
perature. (E.g. function = “heating”)
• Clamps C and 2 = opener
The thermostat closes under increasing temperature and opens in the case of sinking tem-
perature. (E.g. function = “cooling”)
• Clamp
= Earth
The installation may only be carried out by professional installers in accordance with the connec-
tion plan. Furthermore, the installation must also comply with the current VDE regulations and
the specifications of your energy supplier. The installation is always to be carried out with the
power supply disconnected, the security specifications are to be observed. The maximum switch-
ing current indicated in the technical data must be observed!
We accept no liability for any form of misuse.
Operation
The thermostat has a turnable hand dial with a temperature scale. To turn, the dial must be
pulled outwards ca. 5 mm from the housing to release it from the underlying locking mechanism
(cog-teeth). Now turn the dial until your desired temperature aligns with the marking on the
housing.
To lock the setting to the temperature chosen, press the dial downwards on the housing until the
dial engages into the locking system. If you wish to readjust the temperature at a later point in
time, release the dial from the locking mechanism (as described above) and turn it according to
the desired temperature. Then press the dial back in.
1
2
105 mm
50 mm45 mm
Dimensions:
Operating voltage: 230V AC 50Hz
Contact: 1 two-way contact
Switching current: 15 (2) A
Setting range: 30°C - 90°C
Sensor element: Liquid sensor
Protection rating: IP 20
CE approved
Technical data:Circuit diagram:
Thermostat AT 10
Surface mount thermostat
Model AT 10
Article no. 114 100
Produktspecifikationer
| Varumärke: | Salus |
| Kategori: | Termostat |
| Modell: | AT10 |
Behöver du hjälp?
Om du behöver hjälp med Salus AT10 ställ en fråga nedan och andra användare kommer att svara dig
Termostat Salus Manualer
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
28 Juli 2025
28 Juli 2025
28 Juli 2025
28 Juli 2025
28 Juli 2025
28 Juli 2025
Termostat Manualer
- Devolo
- ELKO
- Easy Timer
- Brennenstuhl
- Coati
- Bticino
- Busch-Jaeger
- Heatmiser
- EasyTemp
- Seitron
- Heatit
- Hornbach
- Agpo Ferroli
- Mikoterm
- Arnold Rak
Nyaste Termostat Manualer
1 Augusti 2025
1 Augusti 2025
1 Augusti 2025
1 Augusti 2025
1 Augusti 2025
1 Augusti 2025
30 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025