Axxess AXBT-TY1 Bruksanvisning
Axxess
ej kategoriserat
AXBT-TY1
Läs gratis den bruksanvisning för Axxess AXBT-TY1 (4 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 1.5 recensioner. Har du en fråga om Axxess AXBT-TY1 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
A XBT-TY1
INSTALLATION INSTRUCTIONS
AxxessInterfaces.com © COPYRIGHT 2025 METRA ELECTRONICS CORPORATION REV. 4/18/25 INSTAXBT-TY1
ATTENTION: With the key out of the ignition,
disconnect the negative battery terminal before
installing this product. Ensure that all installation
connections, especially the air bag indicator lights, are
plugged in before reconnecting the battery or cycling
the ignition to test this product.
NOTE: Refer also to the instructions included with the
aftermarket accessory before installing this device.
INTERFACE FEATURES
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink
• Tape • Wire cutter • Zip ties
TABLE OF CONTENTS
Connections ............................................................2
Installation .............................................................2
App Instructions .....................................................3
Data Interface Fits Select Toyota Models
Camry 2018-2023 /RAV4 2019-2023
• Designed for non-amplified models
• Provides NAV outputs (parking brake,
reverse, speed sense)
• Provides power and four speakers
• Pre-wired AXSWC harness (AXSWC sold
separately)
• Retains balance and fade
• Retains the factory backup camera **
• Allows retention and adjustment of the
factory personalization menu*
• Adjust personalization settings via
Bluetooth
®
wireless technology when
used with the AX-CUSTOM-BT app for
smartphones and tablets
Visit AxxessInterfaces.com for more detailed information about
the product and up-to-date vehicle specific applications
OPTIONAL ACCESSORIES
(sold separately)
Steering Wheel Control Interface: AXSWC
APPLICATIONS
Toyota
Camry....................................................... 2018-2023
RAV4 ........................................................2019-2023
INTERFACE COMPONENTS
• AXBT-TY1 harness:
• 10-pin harness
• 28-pin harness
• 30-pin harness
• 12-pin AXSWC harness
• 16-pin AXBT harness
• AXBT interface
*Actual options available vary per vehicle and per trim. (Refer to owner manual for options
available in vehicle)
**Requires the AXCSD-6V (sold separately)
See our Vehicle Fit Guide for up-to-date vehicle-specific applications
2
10-pin harness:
• Connect the Gray wire to the front right positive speaker output.
• Connect the Gray/Black wire to the front right negative speaker output.
• Connect the White wire to the front left positive speaker output.
• Connect the White/Black wire to the front left negative speaker output.
• Connect the Green wire to the rear left positive speaker output.
• Connect the Green/Black wire to the rear left negative speaker output.
• Connect the Purple wire to the rear right positive speaker output.
• Connect the Purple/Black to the rear right negative speaker output
12-pin AXSWC harness & 3.5mm jack:
This 12-pin AXSWC harness & 3.5mm jack are to be used with an AXSWC (sold separately)
to retain steering wheel audio controls. If the AXSWC is not being used, disregard this
harness and 3.5mm jack. If it is to be used, please refer to the AXSWC instructions for radio
connections and programming. Disregard the harness that comes with the AXSWC.
With the key in the off position:
1. Connect the AXBT-TY1 harness to the AXBT interface.
2. Connect the AXBT-TY1 harness to the wiring harness in the vehicle.
3. If an AXSWC (sold separately) will be used, do not connect it until after the AXBT is fully
functional.
CONNECTIONS
I N STALL ATI O N
From the AXBT-TY1 harness to the aftermarket radio:
• Connect the Black wire, the Black wire labeled “CAMERA GROUND”, and also the Black wire
from the AXCSD-6V, to the ground wire.
• Connect the Yellow wire to the battery wire.
• Connect the Red wire to the accessory wire.
• Connect the Red wire labeled “CAMERA POWER 6V”, to the Blue/Red wire from the AXCSD-6V.
• Connect the reverse wire from the aftermarket radio to the Green/Purple wire, and also to
the Blue/White wire from the AXCSD-6V.
The following (2) wires are only for a multimedia/navigation radio that requires these wires.
• Connect the Blue/Pink wire to the VSS/speed sense wire
• Connect the Light Green wire to the parking brake wire
• If retaining the factory AUX-IN jack, connect the Red and White RCA jacks to the audio
AUX-IN jacks from the aftermarket radio.
• Connect the Yellow RCA jack to the backup camera input.
The Bluetooth
®
word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Metra Electronics is under license.
Other trademarks and trade names are those of their respective owners.
Produktspecifikationer
| Varumärke: | Axxess |
| Kategori: | ej kategoriserat |
| Modell: | AXBT-TY1 |
Behöver du hjälp?
Om du behöver hjälp med Axxess AXBT-TY1 ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat Axxess Manualer
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
ej kategoriserat Manualer
- Corberó
- Jung
- Caliber
- Owon
- Heatfab
- Signature Hardware
- Adesso
- Cicada Audio
- Matrix Audio
- GoXtreme
- Duronic
- Tork
- Emerio
- Paraclipse
- Jetson
Nyaste ej kategoriserat Manualer
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025