Webgate OPT-RX1-RS485U Bruksanvisning

Webgate AV förlängare OPT-RX1-RS485U

Läs gratis den bruksanvisning för Webgate OPT-RX1-RS485U (2 sidor) i kategorin AV förlängare. Guiden har ansetts hjälpsam av 29 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 15 recensioner. Har du en fråga om Webgate OPT-RX1-RS485U eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

※ Please read instruction manual carefully before

installing or using this product.

OPT-RX1-RS485U / OPT-TX1-RS485U

OPT-RX16-RS485U / OPT-TX4-RS485U

Instruction Manual

The World’s first certified by

HDcctv Alliance

Precautions

Coax Cable

1. HD-SDI maximum transmission distance depends on

the cable manufacturer or installation environment.

2. The impedance of the coaxial cable and BNC

connectors must be 75 Ohm. For your reference, please

refer to the below table of cable recommendation.

Note) When selecting a cable, consider the maximum

transmission distance of the cable which depends on

its attenuation at 750MHz.

(dB/100m <25dB of attenuation is recommended.)

Cable Type

Length of

HD-SDI

Details of usage

5C2V

About

100M

For analog signal

4C-FB(T), 4C-HFB(T),

About

150M

5C-FB(T), 5C-HFB(T),

L-6CHD, RG6

About

200M

Dedicated cable for HD-SDI

Note) Foamed or High-foamed insulation cable is

recommended.

Note) Double or Triple shielded cable is recommended

Trouble Shooting

EN Rev 1.0

WEBGATE Div. Daemyung Enterprise Co., Ltd.

6F, Hanlim Venture Town B/D, 689-6, Geumjeong-Dong

Gunpo-Si, Gyeonggi-do, Korea

TEL : +82-1644-3421

FAX : +82-31-428-9400

sales@webgateinc.com

support@webgateinc.com

www.webgateinc.com

Premium to your HD-CCTV solution

Device connection method

1. Connect camera’s video output to Transmitter’s “HD-SDI In” using coaxial cable.

- To control camera OSD or PTZ, connect RS485 line between Transmitter and camera.

- Please refer to “NOTICE of coaxial cable” regarding the maximum transmission distance of HD-SDI.

2. Connect Transmitter and Receiver using Single mode LC Type fiber-optic cable.

- When connecting optical cable to the converter, insert fully until you hear a click sound.

- As shown in Figure 1, pull the lever to lock the optical cable not to fall off from the converter.

3. Connect Receiver’s “HD-SDI Out” to DVR’s “HD-SDI In” using coaxial cable.

- To control camera OSD or PTZ, connect RS485 line between Receiver and DVR.

4. Check the status of LED indicators to confirm the correct connections

- Power : Red LED will be lit if the power is on.

- HD-SDI : Green LED will be lit if the video signal enters.

- Optic : Green LED will be lit if Transmitter and Receiver are connected each other.

- RS485 : Green LED will be blinking during data is being entered.

5.Check the monitor that is connected to DVR whether all channels are properly displayed

FIBER OPTIC CONVERTER

Fiber-Optic Cable

1. For cable connection, do not bend the

cable narrower than 30mm

(Minimum allowable refraction range).

2. Do not pull the cable from both ends.

3. Do not spin the optical cable while the

cable is connected to connector.

4. Do not knot the optical cable.

Specification

DVR

Receiver

TransmitterCamera

Fiber Optic Cable

Max. 20Km

Product Features

1. Converting between HD-SDI signal and Optical signal.

Optical signal transmission.

2. Video/Data (RS485) transmission up to 20Km through

single mode fiber-optic cable.

3. Supports 1.5Gbps, 750Mbps for optical signal, and

max. 115200bps for data.

4. Supports 1080p25/30 or 1080i50/60 video.

5. LED indicators for Power, Video, Data and Fiber-optic

Status.

6. 1U 19” rack type (OPT-RX16-RS485U model only).

7. Advanced surge arrestor and ESD protection circuit for

HD-SDI port.

RS485

HD-SDI

Refer to picture No.1

Refer to

picture No.1

RS485

HD-SDI

Picture No.1

LC Type Connector

Accessories

※ Power cord and adapter are supplied only for

OTP-RX4-RS485U and OPT-RX16-RS485U

Trouble & Symptom Way to Solve

Can not turn on the

equipment, and LED

indicators do not work.

√ Check the power is properly

connected to the equipment

√Check the input power voltage

√ If it does not work, please check

the power adapter or replace it

Nothing shows on the

screen.

Can not control camera’s

OSD menu and PTZ

√Check the RS485 connection

among camera, converter and

DVR

√ Check the polarity of RS485(+,-)

√ Check the setting of DVR and

camera. If the setting values such

as Baudrate, Protocol, Address are

not properly configured, camera

control can not be achieved..

Model OPT-RX1-RS485U OPT-TX1-RS485U OPT-TX4-RS485U OPT-RX16-RS485U

Function 1Ch Receiver 1Ch Transmitter 4Ch Transmitter 16Ch Receiver

Video Standard

Resolution

Impedance

Fiber Optic Type

Connector

HD-SDI Length

Fiber Length

Data Channel

Indicator LED

Input Voltage/Current

Operating Temperature / Humidity

Power consumption Max 6.0W Max 30W

Dimension (W x D x H) 140 X 239 X 54 mm 361 X 483 X 44 mm

Weight

Certifications

12 VDC

(Acceptable Input Voltage Range 6V ~ 25V)

HD-SDI SMPTE 292M

SMPTE 274M(1080p25/30, 1080i50/60), SMPTE 296M(720p25/30/50/60)

75 ohm

Single-mode

Approx 150m@L-4CFB(Canare)

Approx 20Km at 1.5Gbps

RS485 Upstream(Remote control from DVR to Camera)

Power(Red), Link-Opt(Green), Link-SDI(Green), RS485(Green)

KC, FCC, CE, RoHS, HDcctv(TBD)

Max 2.0W

65 X 117 X 26 mm

+0°C to +50°C (+32°F to +122°F) 20%RH to 80%RH

※ ※

1Ch TX/RX 4Ch TX 16Ch RX

Installation Power Cable Adapter

Accessories

Fiber Optic Converter

160g 150g 1Kg 4.5Kg

High-foamed, double or

triple shielded cable is

recommended

RG59

√Check video of camera that is

connected to Transmitter. If there

is no video output from camera,

nothing could be shown on the

screen

√Check the power connection of

camera

√Check the cable connections

between camera, converter and

DVR

Produktspecifikationer

Varumärke:	Webgate
Kategori:	AV förlängare
Modell:	OPT-RX1-RS485U
Videolägen som stöds:	1080p, 720p
Maximal upplösning:	- pixlar
Certifiering:	KC, FCC, CE, HDcctv
Modell:	AV-mottagare
Bandbredd:	1.5 Gbit/s
BNC utgångsportar:	1
Driftspänning:	12 V
Kabeltyper som stöds:	Fiber
Produktens färg:	Grå
bruksanvisning:	Ja
Strömförbrukning (vanlig):	2 W
Temperatur vid drift:	0 - 50 ° C
Hållbarhetscertifiering:	RoHS
På / av-knapp:	Ja
Mottagarvikt:	160 g
Mottagare (B x D x H):	117 x 65 x 26 mm
Anslutningstyp:	LC